Where communities thrive


  • Join over 1.5M+ people
  • Join over 100K+ communities
  • Free without limits
  • Create your own community
People
Repo info
Activity
    Igor Zalatov
    @ZigFisher
    timecop1818 [telegram]
    I'm gonna guess: no
    Igor Zalatov
    @ZigFisher
    Pieter [telegram]
    I have an Xiaomi Mijia 2018 (SXJ02ZM); that's a T20 device. I dumped the firmware using a CH431A programmer. Now wanted to try flashing OpenIPC, by writing a firmware directly on the flash memory.
    Basic question perhaps but I need some pointers: how do I merge u-boot, the u-boot uImage, and the OpenIPC rootfs into 1 image, which I can then flash with the CH431A programmer?
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    I’ll remove and backup flash
    Hexplorer [telegram]
    The camera I have with USB data lines connected is Wyze v3, which runs Linux. The one with RT-Thread has a Fullhan FH8830 and is a HikVision doorbell that only has two external wires for 48VAC doorbell transformer. I desoldered & backed up and have full uboot on the doorbell to restore (re @ru67yn41l: I have a cam i think it's like your with unusefull rttread on board the chip is a bk7251 from bekencorp it's like a china A9 cam and serial is connected to usb plug (used only to power it) the serial connection was originally cutout on the board so it needed just a tic of solder iron on tx and rx lines.
    Is your camera like mine?)
    Hexplorer [telegram]
    Seems like Wyze have set the countdown timer in uboot to 0 seconds
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    I tried everything I could think of in RT-Thread but HikVision has customized it and no commands work in the RT-Thread terminal or whatever application is running
    Hexplorer [telegram]
    I thought shorting across some of the test pads or reset button during boot might bring me to uboot prompt but no luck so far
    Hexplorer [telegram]
    There are too many test pads to try every combination
    widgetii [telegram]
    I’d try writing a simple python script which will send Ctl-C many times quicker than human can do
    like this https://github.com/OpenIPC/burn/blob/master/burn#L257
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    Yes seems okay but can’t find roots, which I expected (re @gtxaspec: have you tried to boot the kernel via the factory t31 file?)
    dimerrr [telegram]
    if you wish to boot it that way,you have to build own kernel and specify default cmdline there,that will point to some rootfs
    dimerrr [telegram]
    or even include initramfs
    gtxaspec [telegram]
    Hexplorer erase mtd1 and you can access the uboot command line
    Hexplorer [telegram]
    @widgetii @gtxaspec and anyone else that responded to my messages, want to say thanks. It’s nice to find a community that is willing to help people
    Hexplorer [telegram]
    I was testing if the kernel would start. Haven’t had time to fool with it since
    gtxaspec [telegram]
    test it with the factory file
    Hexplorer [telegram]
    I will erase mtd1 and try that
    gtxaspec [telegram]
    if that works then you know mtd1 will work too
    gtxaspec [telegram]
    you can also load kernel via uboot command from mmc
    FlyRouter [telegram]
    The best "thank you" is PR code to our repositories and support on OpenCollective... 😊
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    I’m not much of a programmer but will submit PRs if I am able to help
    Hexplorer [telegram]
    Have you had issues with donations to OpenCollective from the US?
    Igor Zalatov
    @ZigFisher
    FlyRouter [telegram]
    It's never too late to learn.
    We believe in you, you are persistent... 😊👌 (re @Hexplorer: I’m not much of a programmer but will submit PRs if I am able to help)
    Igor Zalatov
    @ZigFisher
    danielk117 [telegram]
    Hey guys, is there an short instruction about how to install openipc on a Xiaomi MJSXJ02HL? According to your wiki it is a supported device.
    Igor Zalatov
    @ZigFisher
    widgetii [telegram]
    Could you show the link from the wiki?
    Igor Zalatov
    @ZigFisher

    widgetii [telegram]
    got it, it’s based on HI3518EV300 SoC

    here is an interactive manual https://openipc.org/cameras/vendors/hisilicon/socs/hi3518ev300

    Igor Zalatov
    @ZigFisher

    danielk117 [telegram]
    Thank you! Is there an installation method based on sd card? or do I really need to open the case and get serial connection? (re @widgetii: got it, it’s based on HI3518EV300 SoC

    here is an interactive manual https://openipc.org/cameras/vendors/hisilicon/socs/hi3518ev300)

    Igor Zalatov
    @ZigFisher
    metsys1 [telegram]
    assume something not supported:
    dimerrr [telegram]
    a lot of pins == sdio == not supported / or send PR's
    Igor Zalatov
    @ZigFisher
    LouD [telegram]
    Hi3861VL? Have one on the camera I am trying to port to OpenIPC aswell, also SDIO ... :( (re @metsys1: assume something not supported)
    themactep [telegram]
    i won't advise to flash anything without access to serial console. the risk to brick your device is too high. it could be anything, from unsupported wireless card to a glitchy flash chip. (re @danielk117: Thank you! Is there an installation method based on sd card? or do I really need to open the case and get serial connection?)
    metsys1 [telegram]
    (re @LouD: Hi3861VL? Have one on the camera I am trying to port to OpenIPC aswell, also SDIO ... :()Hi3518EV300:
    LouD [telegram]
    I meant the wifi chip, main soc on my cam is an Ingenic T31ZL (re @metsys1: Hi3518EV300)
    metsys1 [telegram]
    no clue 😕 (re @LouD: I meant the wifi chip, main soc on my cam is an Ingenic T31ZL)
    LouD [telegram]
    looks like one
    LouD [telegram]
    LouD [telegram]
    diff logo on the casing is all
    Igor Zalatov
    @ZigFisher
    StealUrKill_PhD [telegram]
    does anyone have any older speco software? looking for the safeguard ip scanner or the multi-clients cms software. cant seem to find a legit file
    Igor Zalatov
    @ZigFisher
    StealUrKill_PhD [telegram]
    Got it. Nevermind (re @StealUrKill_PhD: does anyone have any older speco software? looking for the safeguard ip scanner or the multi-clients cms software. cant seem to find a legit file)
    Igor Zalatov
    @ZigFisher
    danielk117 [telegram]
    Ah great. Thank you for this link 😊 (re @themactep: https://forum.donanimhaber.com/xiaomi-security-camera-1080p-magnetic-mount-mjsxj02hl-repair-fix-it-tear-down-how-to-work--147898319
    this one?)
    Igor Zalatov
    @ZigFisher
    adeelahmed786 [telegram]
    Hi everyone does anyone guide me how this WiFi kit works? Wifi NVR with wifi cameras,wifi cameras can also connect to each other for better reception of signals
    Any Linux commands or any documentation thanks 👍
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    I’ve tried but I don’t get any output after it decompresses the kernel (re @dimerrr: try 8833)
    Igor Zalatov
    @ZigFisher
    carnei_ro [telegram]
    Hey guys, I just flashed my 50H20L_S39 using the coupler file. It is now booting the OpenIPC and it is recognizing the sensor “sc2035” by default….
    Yeah, this sensor is not supported yet, right? 😩
    Is there any workaround?
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    Here are some notes and the steps I followed to write FH8833v100 uImage: https://pastebin.com/bGSF5qPp
    Hexplorer [telegram]
    Maybe I made a mistake
    Igor Zalatov
    @ZigFisher
    carnei_ro [telegram]
    Hey guys, I just flashed my 50H20L_S39 using the coupler file. It is now booting the OpenIPC and it is recognizing the sensor “sc2035” by default….
    Yeah, this sensor is not supported yet, right? 😩
    Is there any workaround?
    Igor Zalatov
    @ZigFisher
    Hexplorer [telegram]
    I’ve tried but I don’t get any output after it decompresses the kernel (re @dimerrr: try 8833)