Where communities thrive
Join over
1.5M+ people
Join over
100K+ communities
Free
without limits
Create
your own community
Explore more communities
esp8266/Arduino
Arduino IDE for ESP8266
People
Repo info
Activity
10:44
dok-net
synchronize
#6047
10:44
dok-net
synchronize
#6902
10:44
dok-net
synchronize
#6782
10:37
dok-net
synchronize
#6857
10:30
ilibx
forked
ilibx/Arduino-1
09:41
ButESP
forked
ButESP/Arduino
09:30
Adarsh995
forked
Adarsh995/Arduino
Dec 13 21:26
earlephilhower
closed
#6910
Dec 13 21:18
resfandiari
opened
#6910
Dec 13 21:17
Vitala1985
forked
Vitala1985/Arduino
Dec 13 19:45
gylmd
forked
gylmd/Arduino
Dec 13 18:41
devyte
synchronize
#6857
Dec 13 18:38
devyte
closed
#6908
Dec 13 17:46
markrhickman
forked
markrhickman/Arduino
Dec 13 17:35
d-a-v
assigned
#6907
Dec 13 17:35
d-a-v
labeled
#6907
Dec 13 17:35
d-a-v
milestoned
#6907
Dec 13 15:56
mosekaj
forked
mosekaj/Arduino
Dec 13 15:23
mike-s123
opened
#6909
Dec 13 14:15
f1lint
forked
f1lint/Arduino
Clemens Kirchgatterer
@everslick
does not
but the first has the disadvantage that i have to redefine ALL build defines
LWIP
DEFINES = -DLWIP
STATS=1 -D
ets
-DICACHE_FLASH -U__STRICT_ANSI
-DLWIP_OPEN_SRC
Me No Dev
@me-no-dev
i never intended to change build flags from command line, therefore I wrote it like that
feel free to make changes and PR
Clemens Kirchgatterer
@everslick
ok, I will play around for some time and make a PR later
Clemens Kirchgatterer
@everslick
hmm, my own compiled lwip feels much slower
FWeinb
@FWeinb
Has anyone tried to remove an esp8266 from a nodemcu? (with just a soldering iron)
Me No Dev
@me-no-dev
yup
mine has qio 4MB module
have hot air?
FWeinb
@FWeinb
No hot air. Kinda impossible to do it with one iron...
Me No Dev
@me-no-dev
kinda impossible with just iron
solder goes under the pads also
FWeinb
@FWeinb
Yeah that will make it impossible to do. To bad.. I just let the magic smoke out on one. To dump to change the multimeter back to voltage...
Me No Dev
@me-no-dev
well I have a crazy idea since you have no other means of salvaging the rest of the board
FWeinb
@FWeinb
I would just like to replace the esp on it.
Me No Dev
@me-no-dev
flux well around the chip, put it on a tray in the oven and set the temp to 220 celsius
monitor the temp and when reached, open the oven and try to pull the module from the board
might need play with the temp, but do not heat too high
FWeinb
@FWeinb
Yeah. That could work.
Me No Dev
@me-no-dev
and watch out not to move any other element from the board
FWeinb
@FWeinb
I hope the nodemcu is still working.
Me No Dev
@me-no-dev
how did you let the smoke?
_
FWeinb
@FWeinb
I did try to measure the voltage on vin to gnd but had the multimeter on current...
Me No Dev
@me-no-dev
so you shorted the LDO?
wait... VIN?
USB 5V or?
FWeinb
@FWeinb
Yes.
Me No Dev
@me-no-dev
if you just shorted those then there should not be any damage to the esp
i also see a diode so your usb-uart should be well also
are you sure you didn't touch another pin than GND with the multimeter?
FWeinb
@FWeinb
There is like 9V between 3V3 and GND now on the broken one.
Me No Dev
@me-no-dev
what are you powering it with?
FWeinb
@FWeinb
Just 5V USB
Me No Dev
@me-no-dev
then how will there be 9V there?
FWeinb
@FWeinb
I have no idea.
Me No Dev
@me-no-dev
your multimeter OK?
FWeinb
@FWeinb
Just used another one. got 1V now.
Me No Dev
@me-no-dev
what do you get on VIN?
FWeinb
@FWeinb
1,75V
Me No Dev
@me-no-dev
that also does not sound right
power goes like this
USB
->
Diode
->
VIN
->
LDO
->
3.3
V
maybe the diode is gone
it's the little black SMD part next to the VIN pin
you can check with the good multimeter between GND and both of it's pins
FWeinb
@FWeinb
No. That one is wrong
Me No Dev
@me-no-dev
oh ok...
let me look
FWeinb
@FWeinb
That one is wrong.