Where communities thrive


  • Join over 1.5M+ people
  • Join over 100K+ communities
  • Free without limits
  • Create your own community
People
Repo info
Activity
    Alex Albino
    @zrecore
    I use an ATMEL-ICE programmer, using the SAM-D port.
    Ashish Mahendra
    @ashi_mahe_twitter
    ok
    Just veryfying with you that if my device has programmed correctly or now
    Ashish Mahendra
    @ashi_mahe_twitter
    not*
    Thanks mate, will buy it today
    Alex Albino
    @zrecore
    it should enumerate as "03eb:6124" (VID, PID)
    np
    Ashish Mahendra
    @ashi_mahe_twitter
    ok
    ICE can be used for all microchip controllers right
    Alex Albino
    @zrecore
    The ATMEL-ICE programmer is used with
    Ashish Mahendra
    @ashi_mahe_twitter
    Thank you
    Alex Albino
    @zrecore
    Programming and on-chip debugging of all Atmel AVR 32-bit MCUs on both JTAG and aWire interfaces
    Programming and on-chip debugging of all Atmel AVR XMEGA® family devices on both JTAG and PDI 2-wire interfaces
    JTAG and SPI programming and debugging of all Atmel AVR 8-bit MCUs with OCD support on either JTAG or debugWIRE interfaces
    Programming and debugging of all Atmel SAM ARM Cortex®-M based MCUs on both SWD and JTAG interfaces
    Programming of all Atmel tinyAVR® 8-bit MCUs with support for the TPI interface
    Ashish Mahendra
    @ashi_mahe_twitter
    Hmm
    Alex Albino
    @zrecore
    ...please see the link I had posted, it contains all the supported devices. MicroChip purchased the Atmel company... so now MicroChip owns and makes the Atmel AVR amd SAM chips
    Ashish Mahendra
    @ashi_mahe_twitter
    Hey is there any chance that i can alter variant file and use Sercoms to alter pin. If i have to do so, which variant should i Change?
    Alex Albino
    @zrecore
    the FemtoUSB uses the
    Ashish Mahendra
    @ashi_mahe_twitter
    @zrecore Thanks
    Working on the device
    spi.PNG
    Spi-1.PNG
    Ashish Mahendra
    @ashi_mahe_twitter
    in above picture, in variant.cpp they have mention SPI as 8 - 10, but in this example code they mentioned as 11-13! Confused
    Please correct me if am wrong
    Alex Albino
    @zrecore
    The SAM D21 E has less pins than the SAM D21G (Arduino Zero chip).
    I had to map the Arduino pins to the physical pin port and number a little differently
    Ashish Mahendra
    @ashi_mahe_twitter
    @zrecore really great job bro
    Alex Albino
    @zrecore
    @ashi_mahe_twitter thanks.
    Ashish M Mahendra
    @navinyate
    @zrecore recebtly I bootloaded ATSAMD21E firmware but, after i program a sample cde into it, the firmware a.k.a bootloade get erased
    Please help me with this
    Alex Albino
    @zrecore
    hi Asish. Would you mind sharing a link to your project code? Perhaps the linker script you are using needs to be checked. I think the SAM-BA bootloader occupies address 0x0 to 0x2000 (without USB support it may be less), and your own code gets saved from 0x2000 and up
    Ashish M Mahendra
    @navinyate
    @zrecore I shall be frank with you, I don't know how to Share link to my project, are you asking for team viewer?
    Am using samd21_sam_ba_both_interfaces.hex from Atmel AT07175: SAM-BA Bootloader for SAM D21
    Alex Albino
    @zrecore
    You may need to host your code on GitHub or bitbucket ...I can't trouble shoot without seeing what is there.
    Ashish M Mahendra
    @navinyate
    Am using the example from your project
    Alex Albino
    @zrecore
    Gitlab is good too
    which example? is it
    Ashish M Mahendra
    @navinyate
    a minute
    Ashish M Mahendra
    @navinyate
    when i was burning bootloader i found this
    yea
    Alex Albino
    @zrecore
    Use that, with Arduino IDE. Which chip are you using? (exact make and model please)
    Ashish M Mahendra
    @navinyate
    ATSAMD221E18A
    Error Register.PNG
    Sry it's ATSAMD21E18A
    in Arduino which Programmer should i have to use
    Ashish Mahendra
    @ashi_mahe_twitter
    Hey
    Ashish M Mahendra
    @navinyate
    ji
    hi