Where communities thrive


  • Join over 1.5M+ people
  • Join over 100K+ communities
  • Free without limits
  • Create your own community
People
Repo info
Activity
  • Feb 24 23:03
    uzi18 commented #519
  • Feb 24 22:16
    lawashnik commented #519
  • Feb 24 12:07
    uzi18 commented #519
  • Feb 24 09:13
    lawashnik commented #519
  • Feb 23 07:47
    uzi18 commented #519
  • Feb 23 04:01
    lawashnik edited #519
  • Feb 23 04:01
    lawashnik opened #519
  • Feb 18 09:24
    gdelconti commented #406
  • Feb 16 05:48
    alifilhan0 opened #518
  • Feb 12 08:14
    uzi18 commented #508
  • Feb 12 08:10
    RoganDawes commented #508
  • Feb 11 12:09
    bilbolodz opened #517
  • Feb 08 08:50
    pilumalu closed #516
  • Feb 08 08:50
    pilumalu commented #516
  • Feb 07 22:32
    uzi18 commented #516
  • Feb 07 22:31
    uzi18 commented #516
  • Feb 07 22:29
    uzi18 commented #511
  • Feb 07 22:15
    uzi18 commented #516
  • Feb 07 21:18
    ccutrer commented #516
  • Feb 07 21:16
    ccutrer commented #511
Thorsten von Eicken
@tve
just connect to port 23
Bonza13
@Bonza13
Explain please where i should connect to port?
Thorsten von Eicken
@tve
something like telnet esp-link.local 23 or do you mean from the web interface?
Bonza13
@Bonza13
Yes web interface of esp-link "µC Console"
Thorsten von Eicken
@tve
the web interface has an input line field, is that not working for you? I probably don't understand what you're trying to so...
Bonza13
@Bonza13
https://i.imgur.com/HTWEJvZ.png
Here screenshot of input line, i thought it will just work like field in serial monitor. But when i send text commands there i only get "Text sent" message and nothing happens on arduino.
Thorsten von Eicken
@tve
it's supposed to work, I'm not sure what's going on in your case...
Edson R Schmidt
@mrximite_twitter
Hi. I'm facing a problem and didn´t found a solution googling.
After burn into a 328p optiboot bootloader, i can send a new .hex and all work fine.
But if I try do send again, is like reset don´t put 328p into programming mode and start to running the on chip firmware
Any tip?
Thorsten von Eicken
@tve
you may have the wrong bootloader or the reset timing of the bootloader isn't compatible with esp-link
Edson R Schmidt
@mrximite_twitter
But why the first time is working?
I´m using mini-core 328p 4mhz external without BOD
Thorsten von Eicken
@tve
it's all a bit messy, unfortunately... the bootloader takes a certain time to be ready and then waits for a certain time before running the current stuff. So one has to hit that not very large time window. Between configuring different baud rates and timings in the bootloader there is no fail-safe solution :-(
Edson R Schmidt
@mrximite_twitter
image.png
Thorsten von Eicken
@tve
It may be that it worked the first time because there was no app loaded? I forget whether optiboot can detect that...
Edson R Schmidt
@mrximite_twitter
Can you sugest some better bootloader to work with my config?

It may be that it worked the first time because there was no app loaded? I forget whether optiboot can detect that...

Yes. Without app loaded this work. Is correct that is a timing reset problem. So what can i do to solve that?

Some other bootloader to try out?
Thorsten von Eicken
@tve
You need the optiboot protocol. You may be able to re-program optiboot with more conventional parameters. It's a frustrating space...
I haven't touched an atmega in several years, so I'm a bit out of the loop, I'm afraid
Edson R Schmidt
@mrximite_twitter
Thansk for your answer.
This is rigth what i want.
And Congratulations for your great work and support.
I'm working on an industrial solution and if work, i want to support you. Have you patreon or someting like?
Thorsten von Eicken
@tve
Thanks for the offer! I don't and that's OK :-).
Edson R Schmidt
@mrximite_twitter
So. Thank You so Much
Edson R Schmidt
@mrximite_twitter
Hi Thorsten
Is there any way to uController to Know ESP-Link Ip address?
I explain. I will send a request to update using a rf433 link. And as soon the ESP-LINK is online, update will be initiate.
Thorsten von Eicken
@tve
there is not. you'd have to add a serial command to support that.
Bartłomiej Zimoń
@uzi18
@mrximite_twitter it is already supported by dannys query-ip branch
Bartłomiej Zimoń
@uzi18
@barthand you can find latest build in isssue #480
Edson R Schmidt
@mrximite_twitter
@uzi18 Can you give me the right direction to that branch?
Edson R Schmidt
@mrximite_twitter
Hi. Anyone have a documentation of API for ElClient?
Since "A prelimenary documentation for the library is available on ELClient API Doc." does not give any answer.
Bartłomiej Zimoń
@uzi18
Look into @dannybackx repositories there is fork of Elclient lib and esp-link
@mrximite_twitter found it?
Edson R Schmidt
@mrximite_twitter
No. There is nothing about Elclient
Ops
Found...
Marcel Zuidwijk 
@zuidwijk_twitter
Is it possible to add a pre-config while flashing esp-link?
I'd like to flash 40-ish esp's and all need the setting esp12-swap
(I've googled yet couldn't find the answer yet)
Thorsten von Eicken
@tve
the default settings are in the code, so you'd have to change there
Bartłomiej Zimoń
@uzi18
@zuidwijk_twitter it is possible to rebuild firmware with different default setting s
Marcel Zuidwijk 
@zuidwijk_twitter
Ah ok, so no other way like a config file something? Guess i have to learn to compille/build a new firmware than ☺️
Bartłomiej Zimoń
@uzi18
@zuidwijk_twitter it is possible to get one settings from one module and patch it with eg. Only IP address but you need to know where change data in flash dump
lawashnik
@lawashnik
Hi. Can someon help me with gpio? Is it possible to manage not used gpio state? Maybe curl requests or something? I can't find an unswer in github.
Bartłomiej Zimoń
@uzi18
@lawashnik Actually it is not supported