These are chat archives for nightscout/intend-to-bolus

13th
Jan 2017
Scott Leibrand
@scottleibrand
Jan 13 2017 00:02
@C-Ville correct, xdrip is only in oref0 dev
C-Ville
@C-Ville
Jan 13 2017 00:03
I am somewhat confused where to tell xdrip to send data to my edison
dougtakeuti
@dougtakeuti
Jan 13 2017 00:11
So Julia had the (10-day) sensor break she had been asking for while we were in a fairly remote area of Brazil. She was on MDI during the day and on the pump at night, completely offline. We started the sensor 20 h ago and resumed the loop 10 hours ago, but the BG's are not uploading to NS. I haven't touched the rig, so that's a suprise to me. Anything in particular I should be looking for as I debug?
C-Ville
@C-Ville
Jan 13 2017 00:28
reading the docs in the .xdrip directory seemed to help :-)
xDrip > Settings > REST API Upload > Set Enabled and enter Base URL: http://[API_SECRET]@[Pi/Edison_IP_address]:5000/api/v1/
Aaron Michelson
@Aaybob
Jan 13 2017 01:13
Freshly flashed edison....do I have the correct linux version?
root@red:~# uname -mrs
Linux 3.10.17-poky-edison+ i686
Aaron Michelson
@Aaybob
Jan 13 2017 01:19
Using dev I can't initiate bluetoothctl interactive program.

root@red:~# sudo /usr/local/bin/bluetoothd --experimental &
1 6076
root@red:~# sudo: /usr/local/bin/bluetoothd: command not found

1+ Exit 1 sudo /usr/local/bin/bluetoothd --experimental

porkupan
@porkupan
Jan 13 2017 01:24
@Aaybob when running oref0-setup you need to have a btmac specified. Then the script will install bluez-5.37 BT library.
Aaron Michelson
@Aaybob
Jan 13 2017 01:25
@porkupan true. it would have taken longer if bluez was installed
porkupan
@porkupan
Jan 13 2017 01:26
Something similar to this:
# src/oref0/bin/oref0-setup.sh --dir=/home/edison/xxx --serial=xxx --cgm=G4 --ns-host=http://xxx.herokuapp.com --api-secret=xxx --tty=/dev/spidev5.1 --enable=' autosens  meal ' --radio_locale='US' --max_iob=4 --btmac="xx:xx:xx:xx:xx:xx"
You can install bluez manually, of course. Or rerun script.
JaysonEwer
@JaysonEwer
Jan 13 2017 01:34
@dougtakeuti are you using Dexcom share?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 02:58
hello this is my first post. I have the rp3 dex share 4 nightscout and I am stuck in the very beginning steps of this process
i am attempting to set up openaps for my son
Dana Lewis
@danamlewis
Jan 13 2017 03:02
Welcome @ryan_anglani_twitter
What step are you stuck at? What did you successfully do last?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 03:15
I think I downloaded a program to work the sd card
Luis Betancourt
@betluis
Jan 13 2017 03:20
Hello, I am trying to go through phase 1 of oref0-setup for a pi and for some reason it does not let me run the command. would anyone help me understand why?
this is what I get: pi@raspberrypi:~ $ sudo mkdir -p ~/src; cd ~/src && git clone git://github.com/openaps/oref0.git || (cd oref0 && git checkout master && git pull)fatal: could not create work tree dir 'oref0'.: Permission denied
-bash: cd: oref0: No such file or directory
it says permission denied, which I though shouldn't be if I use sudo
Dana Lewis
@danamlewis
Jan 13 2017 03:22
@betluis you did step 0 prior to this successfully?
You shouldn't need sudo for step 1..
Luis Betancourt
@betluis
Jan 13 2017 03:23
yes using sudo
step 0 went on fine
Dana Lewis
@danamlewis
Jan 13 2017 03:24
@ryan_anglani_twitter you might need to tell us a little more about what page of the docs you are on; what step you are attempting and struggling with now.
Luis Betancourt
@betluis
Jan 13 2017 03:25
without using sudo I get the same access denied answer
pi@raspberrypi:~ $ mkdir -p ~/src; cd ~/src && git clone git://github.com/openaps/oref0.git || (cd oref0 && git checkout master && git pull)
fatal: could not create work tree dir 'oref0'.: Permission denied
-bash: cd: oref0: No such file or directory
Dana Lewis
@danamlewis
Jan 13 2017 03:26
Is this a brand new Pi?
Luis Betancourt
@betluis
Jan 13 2017 03:27
it is a brand new card yes
I am starting from scratch
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 03:28
I downloaded the 7-zip installer @danamlewis
Luis Betancourt
@betluis
Jan 13 2017 03:28
the pi is not new, the card I just formated it
Eric
@ecc1
Jan 13 2017 03:29
The problem is that your first sudo command created ~/src owned by root, and the subsequent commands couldn't write there. Try "sudo rmdir ~/src" and then do the whole line again without sudo.
Luis Betancourt
@betluis
Jan 13 2017 03:31
@ecc1 ok, let me try that...
@ecc1 it worked.. please help me understand this.. the problem happened because I shouln't have used sudo in step 0?
Eric
@ecc1
Jan 13 2017 03:34
Correct. "sudo" makes everything in that command (up to the first semicolon) run as the root user.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 03:34
setting up your raspberry pi is the page I'm on @danamlewis
Luis Betancourt
@betluis
Jan 13 2017 03:35
@ecc1 thanks!
Eric
@ecc1
Jan 13 2017 03:44
Sorry, I'm not familiar with the openaps setup process, I'm just very familiar withthe Unix command line and happened to see the problem you were having. :-) I'm sure others who have done the install recently will be hable to help.
Luis Betancourt
@betluis
Jan 13 2017 03:45
well, I appreciate your help. thank you
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 04:13
can anyone answer my question? I am reading through the openaps instructions and it says rpi2 i have the rpi3 is that ok?
fiberfan
@fiberfan
Jan 13 2017 04:17
@ryan_anglani_twitter I think I followed the directions as written for my rpi3.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 04:19
i feel stuck
ejoe132
@ejoe132
Jan 13 2017 04:29
@ryan_anglani_twitter I set up a pi3 following the directions even though it says pi2, worked fine.
@ryan_anglani_twitter where are you stuck at? Your trying to download 7Zip to install Jessie?
Dana Lewis
@danamlewis
Jan 13 2017 04:40
@ecc1 :+1: @betluis wherever there are lines like that from the docs, try copying and pasting directly - saves a lot of headaches vs trying to type or add things to it. The docs should be very clear if it needs sudo - otherwise don't add it unless specified.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 04:40
@ejoe132 i believe i installed the 7zip
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 04:46
Hello! I'm working on setting up an #openaps system and am getting ""Untracked files: [long list of files] nothing added to commit but untracked files present" when I run openaps init.
Does anyone have experience troubleshooting this? I'm trying to wrap my head around it -- I think I need to do something to start including/tracking those files in my commit? I'm pretty new to rpi, so any tips on how to troubleshoot would be very appreciated! Thanks in advance :)
Dana Lewis
@danamlewis
Jan 13 2017 04:48
Welcome @melodyandrews - are you trying to build from scratch, or have you already successfully set up with the phase 2 setup scripts?
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 04:51
@danamlewis I did set up with the phase 2 scripts and briefly had my pi talking to the pump a few days ago, but since I was waiting on a portable battery pack, the pi was tethered to my wall outlet. Now I've got a battery for it, booted up my pi tonight, and noticed the "untracked files" issue
Dana Lewis
@danamlewis
Jan 13 2017 04:52
What happens when you tail the logs?
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 04:55
tail -F /var/log/openaps/pump-loop.log
determine-basal://text/shell/enact/suggested.json
reporting enact/suggested.json
{"reason":"BG data is too old (it's probably this), or clock set incorrectly. The last BG data was read at Mon Dec 26 2016 23:54:00 GMT-0500 (EST) but your system time currently is Thu Jan 12 2017 23:52:11 GMT-0500 (EST)"}
{"reason":"BG data is too old (it's probably this), or clock set incorrectly. The last BG data was read at Mon Dec 26 2016 23:54:00 GMT-0500 (EST) but your system time currently is Thu Jan 12 2017 23:52:11 GMT-0500 (EST)"}
Waiting for ntpd to synchronize... OK!
cat: enact/enacted.json: No such file or directory
Settings less than 10m old
Pumphistory-24 less than 20m old
Completed pump-loop at Thu 12 Jan 23:52:12 EST 2017
Dana Lewis
@danamlewis
Jan 13 2017 04:56
How does your rig normally get CGM data?
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 04:57
@danamlewis carelink stick
Dana Lewis
@danamlewis
Jan 13 2017 04:57
Medtronic CGM?
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 04:57
yes
Dana Lewis
@danamlewis
Jan 13 2017 04:58
Has it successfully continued and enacted a temp yet?
(Not sure about the initial file stuff, but may not matter if you're looping successfully)
Tim Street
@tim2000s
Jan 13 2017 04:59
@Aaybob Yes, I wrote that :smile:
ejoe132
@ejoe132
Jan 13 2017 04:59
@ryan_anglani_twitter were you able to get rasbian jessie installed?
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:00
It did once, but not since the initial setup. Nothing tonight...
Matthias
@ceben80
Jan 13 2017 05:01
morning, I know someone who must cron schedule a reboot every 30 min or so....otherwise the Carelink was hanging so often, looping without reboot was not possible
Dana Lewis
@danamlewis
Jan 13 2017 05:01
Ok, what are the logs erroring on, if anything? (And also - you have a sensor running right now, right?)
Matthias
@ceben80
Jan 13 2017 05:02
Hi Dana :wink:
Luis Betancourt
@betluis
Jan 13 2017 05:03
@danamlewis thanks. got the message
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:04
@ejoe132 I will do that now
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:04
I do have a sensor running now, yes. Tailing the logs looks like it's telling me BG data is too old
Dana Lewis
@danamlewis
Jan 13 2017 05:04
@ceben80 :wave:
Yea - if you have a sensor live that's odd, esp since it says it is fetching pump history. What is the date and time on your pump?
ejoe132
@ejoe132
Jan 13 2017 05:05
@ryan_anglani_twitter awesome
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:06
@danamlewis Friday Jan 13, 12:06am
Dana Lewis
@danamlewis
Jan 13 2017 05:07
Hm. Wonder if there's a buggy record in the pump messing things up somehow. Not sure if anyone has heard of this before, maybe @tmecklem or someone else who's had their hands deep in Medtronic records may have some troubleshooting suggestions.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:08
ok now I should Write Raspbian to the Micro SD Card? @ejoe132
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:09
Hmm ok -- I'm still figuring out gitter, any tips on the best way to broadcast the issue and figure out if anyone else has seen this too? Would wiping my data and starting fresh likely make any difference?
Dana Lewis
@danamlewis
Jan 13 2017 05:10
You could try running the setup script again and see if that magically fixes something - wouldn't hurt, you'll just want to disable your current cron first
And for broadcasting, sometimes it just takes a while for someone to pop in and suggest things to try next - you can tag people if you know they're on a similar setup (i.e. Medtronic CGM) but given time zones, you may want to ask in here again tomorrow if you don't get any other suggestions by then.
The next resort after a day might be to email OpenAPS-dev Google group, as not everyone hangs out on gitter all the time :smile: but usually someone out of the dozens that do will have ideas or solutions on how to resolve.
ejoe132
@ejoe132
Jan 13 2017 05:13
@ryan_anglani_twitter yes
@ryan_anglani_twitter did you download the app to write it? believe its called win32 or something, ill check
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:14
@danamlewis Cool, I will! Thank you so much for your help. I'll ask around again tomorrow or this weekend before I try a clean reload.
ejoe132
@ejoe132
Jan 13 2017 05:15
@ejoe132 win32diskimager
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:15
thank you so much for helping me i have never done this much so far @ejoe132
Dana Lewis
@danamlewis
Jan 13 2017 05:15
@melodyandrews :+1: and don't be shy about asking again - sometimes there's lots of chatter in here about different issues and instances, so never hurts to ask a few hours or a day later again if your initial Q gets buried
ejoe132
@ejoe132
Jan 13 2017 05:16
@ryan_anglani_twitter no worries at all, was and am still in the same place, just got my loop started wednesday 4am !
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:17
so exciting ! @ejoe132
Dana Lewis
@danamlewis
Jan 13 2017 05:18
@ryan_anglani_twitter :+1: if you find anything obvious missing from the docs, please make notes and PR suggestions in later :smile:
Melody Andrews-Caron
@melodyandrews
Jan 13 2017 05:18
@danamlewis That's good to hear. I'm pretty new at all of this - eager to learn, but jumping into a group of experts feels a bit intimidating! - I don't want to pester folks if an issue should be easy to troubleshoot, but for this one I haven't been able to find anything that explains it
I'll definitely check back this weekend :). I appreciate all of your help, thanks!
Dana Lewis
@danamlewis
Jan 13 2017 05:20
:+1: we're all experts (or experienced) at various bits, but no one is an expert/experienced to the same degree at all of it :smile:
@ejoe132 congrats!
ejoe132
@ejoe132
Jan 13 2017 05:21
@danamlewis thank you, truly is awesome. And thank you, thank you for doing all this and helping others.
Dana Lewis
@danamlewis
Jan 13 2017 05:23
:+1: :raised_hands: :clap: :confetti_ball:
Thanks to you too (and everyone else!) for continuing and paying it forward!
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:25
Thank you!!! @danamlewis Have been wanting to complete this system for a long time and after last night of ZERO SLEEP with my lil dude it we beyond time to get this up and running
Dana Lewis
@danamlewis
Jan 13 2017 05:25
Awww
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:26
@ejoe132 ok I now have win32disk
JELCRAWFORD
@JELCRAWFORD
Jan 13 2017 05:27
@Aaybob - thanks for posting that link, @tim2000s - thanks for writing the data up! - I was looking for data today and hadn't yet come across this article. I see it is FIAsp is not yet approved for pediatrics , and the BC Lispro is still awaiting approval...... Data looks encouraging though - this is where we are still waiting I guess....
Matthias
@ceben80
Jan 13 2017 05:34
@ryan_anglani_twitter be careful when using Win32DiskImage when u have a additional hard disk attached to your PC, in case you are not selecting the sd card for writting possible to delete all data on a attached disk, in short, verify carefully your sd card letter before image writting
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 05:35
thank you @ceben80
Tim Street
@tim2000s
Jan 13 2017 05:44
@JELCRAWFORD Approvals tend to come in phases so lack of paeds isn't a surprise. BCLispro slowness is though. Still awaiting a Lilly decision on Phase Iii trials.
JELCRAWFORD
@JELCRAWFORD
Jan 13 2017 05:58
@tim2000s - so first FIAsp... (waiting is not my best thing!)
woodtrevor
@woodtrevor
Jan 13 2017 07:03
@ceben80 What problems were you seeing with the Carelink hanging? If you see "ACK is 0 bytes" errors in the log it can be fixed programmatically, without rebooting. That is the only error I have seen where the Carelink won't recover on its own.
Matthias
@ceben80
Jan 13 2017 07:10
Don't know....as said someone told me @woodtrevor on longterm get rid of this Carelink, poor range, and order a TI Stick
Details in Oskars Wiki......
woodtrevor
@woodtrevor
Jan 13 2017 07:13
I've had pretty good luck with Carelink. I wonder if they aren't all equal...
Matthias
@ceben80
Jan 13 2017 07:14
But the range is sooo horrible :astonished:
Dana Lewis
@danamlewis
Jan 13 2017 07:16
Pump ranges seem to differ, too. So maybe @woodtrevor has the best carelink range in the world + best pump range? ;) :smile:
woodtrevor
@woodtrevor
Jan 13 2017 07:17
Haha. Maybe... :) Mine is 15 feet away right now and working!
Dana Lewis
@danamlewis
Jan 13 2017 07:18
Bet it's a cinnamon flavored carelink ;)
woodtrevor
@woodtrevor
Jan 13 2017 07:21
Hmm... Lemme check... :wink:
...can't wait to get my explorer board though for portability.
j4cbo
@j4cbo
Jan 13 2017 07:41
my pump and enlite transmitter would lose connection if they were on opposite sides of my belt
(and I easily sleep through those alarms if the pump is under the covers)
aaaaaaaand that's why I'm getting a Dexcom
PieterGit
@PieterGit
Jan 13 2017 08:20
@alternateal : to you use the extra dexusb option of oref0-setup.sh to get the cgm data from the dexcom receiver?
woodtrevor
@woodtrevor
Jan 13 2017 10:08
Add
fezulin
@fezulin
Jan 13 2017 11:26
@woodtrevor @j4cbo Over the night I have to tie the Carelink directly on my pumps display. Even if I tie the Carelink on the backside of the pump, I have no connection. :worried: This is annoying, because I cannot easyly see my pumps display. I will replace the Carelink as soon as possible.
Matthias
@ceben80
Jan 13 2017 12:29

@/all Explorer Board Users - Q, this here again with rootcredentials :question: or login with edison?

https://github.com/EnhancedRadioDevices/915MHzEdisonExplorer_SW#setup

Matthias
@ceben80
Jan 13 2017 12:35
could not find a WWrelease?
Jason Wittmer
@jbwittmer
Jan 13 2017 13:01
@ceben80 I think we did all setup with root including command you referenced above. I don't know about your question re: hex file
Matthias
@ceben80
Jan 13 2017 13:02
I am located in Germany, so my q to WW file not US :wink:
but I will start the setup with WWparameter and see what's the result...
Aaron Michelson
@Aaybob
Jan 13 2017 13:43
@melodyandrews did you run:
dpkg-reconfigure tzdata # Set local time-zone
I don't know if the medtronic sensor ... could in need a recharge?
Chris Oattes
@cjo20
Jan 13 2017 13:43
Can anyone do me a favour and run nightscout ns $NIGHTSCOUT_HOST $API_SECRET latest-treatment-time and tell me what it returns? Does it return json, or 0
Aaron Michelson
@Aaybob
Jan 13 2017 13:45

root@red:~/myopenaps# nightscout ns $NIGHTSCOUT_HOST $API_SECRET latest-treatment-time
Unknown request:

openaps use ns shell get entries.json 'count=10'
openaps use ns shell upload treatments.json recently/combined-treatments.json

Aaron Michelson
@Aaybob
Jan 13 2017 13:59
@fezulin I was doing that too. Then my RPi2 stopped working. I installed all the latest software on RPi3 and the range was much larger, just in the same room is all I tested. But my CareLink froze sometime every night so I put PREFLIGHT back in. I ran my loops, two minutes later PREFLIGHT. Three minutes after that loop again. So everything on five minute cycle. @woodtrevor @j4cbo
Tim Street
@tim2000s
Jan 13 2017 14:13
@ceben80 I didn't install that. Just the base subg_rfspy and it seems to have worked fine.
Matthias
@ceben80
Jan 13 2017 14:17
Thanks Tim @tim2000s
Tim Street
@tim2000s
Jan 13 2017 14:31
Been running this version of Edison/explorer for two weeks now and this afternoon I noted that it had stopped communicating with the pump. In the sys log I see this mraa error "Jan 13 14:28:16 ed209 libmraa[11225]: libmraa version v1.5.1-16-g3bd590c initialised by user 'root' with EUID 0
Jan 13 14:28:16 ed209 libmraa[11225]: gpio214: init: Failed to write to 'export': No such device
Jan 13 14:28:16 ed209 libmraa[11225]: edison: Arduino board not detected, assuming Intel Edison Miniboard"
Actually,let me correct myself. It can and does interrogate the pump, but isn't doing the enact function correctly. Nothing has changed on my oref0 set up. Any ideas? Nothing shows in pump-loop logs.
Tim Street
@tim2000s
Jan 13 2017 14:38
Ignore. Git propagation was the issue. No space left.
Chris Oattes
@cjo20
Jan 13 2017 14:39
I don't know about anyone else, but my aps feels like it has become less stable recently
porkupan
@porkupan
Jan 13 2017 14:41
@cjo20 less stable in what sense?
Chris Oattes
@cjo20
Jan 13 2017 14:42
I'm having to spend more time making sure it's working
porkupan
@porkupan
Jan 13 2017 14:51

I have the opposite feeling after making a few changes. But I need to wait a few days before I could say for sure. I am running oref0, however (as of a couple of weeks ago, but with some mods). It seems that my instabilities came from two sides - the RF hang-ups and the network switching.

After the serial_rf_spy.py mod I told you about there has not been a single hang-up of the RF yet. Of course, it's been only 40 hours or so. I also modded the oref0-online.sh script to make it not to attempt the network switching every single time it fails to obtain the IP address from the icanhazip.com, and also to not restart the bluetoothd unless it is not running.

Chris Oattes
@cjo20
Jan 13 2017 14:52
I've still got the delay in mine, and i'm still getting a lot of RF errors
porkupan
@porkupan
Jan 13 2017 14:53
Well, there is only one of those errors that's unrecoverable - the "busy" error. I haven't seen it yet. In fact, my RF has been remarkably stable since the last fix.
Tim Street
@tim2000s
Jan 13 2017 14:57
0.1.5 with master on Explorer has been very stable (apart from the git issue I just had)
porkupan
@porkupan
Jan 13 2017 14:59
Last night at home I had trouble getting to the rig over IP/WiFi for a few minutes. I was about to reset it, thinking the rig was hung, but then the rig became accessible again. Looking into the network log I realized that an intermittent failure to reach icanhazip.com forced a network switchover to BT. I am not sure it's of interest to anyone, but I can post my scripts changes when I get access to the rig at home. They are minor.
porkupan
@porkupan
Jan 13 2017 15:06
@tim2000s I guess it depends on what's stable. If it's been running for a few days without any need for reboot/reset, providing you with OpenAPS functionality, getting good data from the pump, switching seamlessly between WiFi and BT tether, I would say that it is indeed very stable. I work in the Air Traffic Control field where embedded devices must run 24/7/365 without the need to be restarted. So for me the Explorer-based OpenAPS setup has been feeling extremely unstable.
Matthias
@ceben80
Jan 13 2017 15:09
Q to the Explorer board: the cron later is running in rootor edisoncontext :question:
porkupan
@porkupan
Jan 13 2017 15:09
root
There is nothing that's running in edison context. Everything is running as root.
Matthias
@ceben80
Jan 13 2017 15:11
thanks
Colin Lennon
@colinlennon
Jan 13 2017 15:11
@tim2000s What did you do to fix that Tim, a reboot? I've had a few instances on my Explorer rig where /tmp has reached 100% and I've had to run rm -f git*. I've also had a few times where I've been away from a computer and my rig has stopped responding. I couldn't SSH onto it from my phone, so I rebooted it and that got it back up and running. I suspect it might've been the same git propagation issue at those times too.
Would be good to figure out how to avoid that happening
Jason Wittmer
@jbwittmer
Jan 13 2017 15:13
I finally got my first run of Autotune running. Can someone explain to me the advantage of multiple "runs" versus one run? What do the extra runs do?
Tim Street
@tim2000s
Jan 13 2017 15:25
I've sledgehammered it with a daily crontab entry doing 'rm -rf /tmp/git*'
John Benjamin
@Bender1061
Jan 13 2017 15:45
So I'm in a plane right now, pancreabble running talking to my pebble and it's working great! Nice being able to see my IOB at a glance with no need for network access.
Colin Lennon
@colinlennon
Jan 13 2017 15:58
@tim2000s Yeah, I might just do that as well then. It's not pretty, but it's effective!
@ceben80 :clap: :smile:
dougtakeuti
@dougtakeuti
Jan 13 2017 16:09
@JaysonEwer No, I'm using MDT Enlite so I use the Explorer rig to upload cgm data to NS
David
@dakago
Jan 13 2017 16:14
Hello, mmtune is returning -99 for the explorer for the majority of the time. Is this a problem? It is still able to make the loop but the connection seems to drop quite a bit.
Chris Oattes
@cjo20
Jan 13 2017 16:17
Does ccprog work for anyone else with the explorer board?
j4cbo
@j4cbo
Jan 13 2017 16:17
also, i noticed the explorer board has LiPo-handling circuitry onboard... is there a recommended battery that fits nicely?
tazitoo
@tazitoo
Jan 13 2017 16:30
@cjo20 - yeah, ccprog has worked for me to reflash the Explorer
Chris Oattes
@cjo20
Jan 13 2017 16:31
@tazitoo: What command line did you use?
tazitoo
@tazitoo
Jan 13 2017 16:31
lemme check
'''wget https://github.com/EnhancedRadioDevices/subg_rfspy/releases/download/v0.8-explorer/spi1_alt2_EDISON_EXPLORER_US_STDLOC.hex
ccprog -p 19,7,36 erase
ccprog -p 19,7,36 write spi1_alt2_EDISON_EXPLORER_US_STDLOC.hex'''
Chris Oattes
@cjo20
Jan 13 2017 16:32
hmm, that gives me an error
porkupan
@porkupan
Jan 13 2017 16:33
@cjo20 You may want to disable crontab and reboot first, just to make sure there is no conflict with the running openaps processes.
tazitoo
@tazitoo
Jan 13 2017 16:34
@j4cbo - i've been looking at 2000 maH lipos that have '103450' form factor
with these dimension: H=10mm W=34mm L=50mm
porkupan
@porkupan
Jan 13 2017 16:36
I've got this one off eBay. Works perfectly so far. http://www.ebay.com/itm/172264702655
Chris Oattes
@cjo20
Jan 13 2017 16:37
edison@ediscout2:~/src/ccprog$ sudo ./ccprog -p 19,7,36 erase
[sudo] password for edison:
Using pins: DC=19, DD=7, RESET=36
Erasing chip.
could not update FWT!
Chip erase failed.
Guess I'll have to use my cc-debugger when I get home
tazitoo
@tazitoo
Jan 13 2017 16:40
long shot - don't use 'sudo', just log in as root
Chris Oattes
@cjo20
Jan 13 2017 16:41
It does the same thing if I use su - then run it
Dana Lewis
@danamlewis
Jan 13 2017 16:41
@j4cbo re battery, check the Edison hardware page on the docs - one linked now
j4cbo
@j4cbo
Jan 13 2017 16:46
thanks!
RedCyclist1
@RedCyclist1
Jan 13 2017 17:02
Does anyone know how to check the status of my edison board order? I was in the 2nd groupgets order.
ejoe132
@ejoe132
Jan 13 2017 17:09
@RedCyclist1 when was the final order day for 2nd order? was that the one that eneded 12-27-16?
Dana Lewis
@danamlewis
Jan 13 2017 17:10
@RedCyclist1 email ERD to ask, probably
garykidd
@garykidd
Jan 13 2017 17:14
been focusing on other things over last few weeks..... was curious if anyone ever was able to get xdrip g5 working with iphone....or if any updates have been made for offline looping...and later syncing with NS..
my transmitter/receiver are OOW and was contemplating g4 instead of my current g5 on account of a lot of missed data on g5 mobile/iphone...any thoughts?
Dana Lewis
@danamlewis
Jan 13 2017 17:19
that’s one of the reasons I don’t want to go to g5 myself - keep hearing that (missed data) :(
RedCyclist1
@RedCyclist1
Jan 13 2017 17:22
@ejoe132 Yes, My receipt says 12/28. @danamlewis Okay, I'll email them if I don't hear something soon. I already have my Edison board and obviously meant my explorer board.
Dana Lewis
@danamlewis
Jan 13 2017 17:22
:+1:
Tim Street
@tim2000s
Jan 13 2017 17:23
Running G5 on xDrip for a few days had what seemed like a lot fewer dropouts than on iPhone. That includes sensor ???, signal lost, lost transmitter, app hangs, etc.
The dev setup branch now includes the xDrip-APS stuff that @colinlennon has done, using mongo upload for NS and rest to the device for offline looping. Haven't tried that yet.
Chris Oattes
@cjo20
Jan 13 2017 17:42
oops, dead c1110. Definitely trying with cc-debugger when I get home
porkupan
@porkupan
Jan 13 2017 17:43
did you manage to erase them, but could not program?
seems that you should have complete programming (and debugging) access through the gpio's.
jmcrawford
@jmcrawford
Jan 13 2017 18:02
@ceben80 Looking at the contents of your Eddy case, is your Edison connected to the Intel Breakout board? Is your xDrip hardware tied to the edison, or merely co-habitating the case?
Matthias
@ceben80
Jan 13 2017 18:13
@jmcrawford my Eddie (not Explorer Board) is connected to the Intel Mini Breakout Board with additional power wires from J2 to the Wixel
ejoe132
@ejoe132
Jan 13 2017 18:19
@RedCyclist1 curious what you find out, if I remember right it is a four week lead time. So Im expecting mine in the next 2 or so weeks
At what voltage do most people see their pumps going into low battery mode(shut off connectivity? NS says mines at 1.19v and just wanna start carrying a battery if Im getting close, NS has it in red so assumed it was close
j4cbo
@j4cbo
Jan 13 2017 18:29
What do people tend to use for fingerstick meters with openaps? I used my OneTouch UltraLink until it died and replaced it with an Ultra Mini. The integration between the UltraLink and Enlite was really nice, but I guess there's no equivalent with Dexcom?
ejoe132
@ejoe132
Jan 13 2017 18:32
@j4cbo I had a ultra link til it died, then bought a off the shelf one touch cause I have tons of strips I dont wanna just throw away, but I find the one touch to be very inaccurate, can test once and get a readying then test again and be 40 different, though I dont think our meters are that accurate in general. Just my experience
j4cbo
@j4cbo
Jan 13 2017 18:38
nod
the Dario looks like an interesting idea but the reviews are pretty crap
William Fallon
@inform880
Jan 13 2017 18:41
With reading the dex calibrations, I get some traceback errors. Can you even read the calibrations if you don't have "real" bgs?
ejoe132
@ejoe132
Jan 13 2017 18:49
@j4cbo hadnt seen the dario before, neat Idea. Im never sure how I feel about "iphone add ons" one one hand makes things smaller and only need one charger, but if something happens to the phone your stuck til you can get another. Haha only say cause Ive tipped my kayak and had to wait two days for iphone to dry enough the screen came back to life, though dexcom reciever was fine right away
Tim Street
@tim2000s
Jan 13 2017 18:58
Not sure about the bad reviews. I found the Dario pretty good.
j4cbo
@j4cbo
Jan 13 2017 19:13
@tim2000s does it integrate with the Dexcom at all or do you still have to manually copy numbers around?
Tim Street
@tim2000s
Jan 13 2017 19:14
Nothing integrates with the Dexcom app.
j4cbo
@j4cbo
Jan 13 2017 19:20
alas.
garykidd
@garykidd
Jan 13 2017 19:20
anyone try it yet.
j4cbo
@j4cbo
Jan 13 2017 19:33
huh! interesting
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 19:33
hello everyone am I downloading Putty to my laptop or the rpi3?
ohh I think its the pi
jaylagorio
@jaylagorio
Jan 13 2017 19:36
@ryan_anglani_twitter To your laptop
It's a Windows program
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 19:36
@jaylagorio thank you!
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 19:42
I typed in sudoraspi-config and it says command not found
jaylagorio
@jaylagorio
Jan 13 2017 19:44
sudo raspi-config I think
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 19:46
@jaylagorio yes yes yes thank you !!!
Dana Lewis
@danamlewis
Jan 13 2017 19:47
@ryan_anglani_twitter one thing that will save a lot of heartache - copy and paste any specific commands from the docs vs trying to type.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 19:52
ok thank you that makes sense @danamlewis
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:01
I don't see where I can enter a password in the putty program and when I hit enter it says (unable to open connection to raspberrypi.local
Andy Sharrow
@dramageek
Jan 13 2017 20:03
I'm coming up on due-for-a-new-transmitter time (mine's still fine, but if they're going to give me a new one and insurance is going to pay for it, why not keep a backup?). I only switched to Dexcom 6 months ago, and at that time I went with the G4 rather than G5. My current setup: G4 > Share Receiver > xDrip+ on Android >NS >OpenAPS.
So what are peoples experiences with the G4 vs G5? @danamlewis and @garykidd touched on the reliability earlier, but how flaky is it really?
Shorter transmitter life isn't an issue, as my insurance covers it. If I can skip the receiver and go direct to my phone that'd be great, but too many missed readings are obviously a dealbreaker.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:04
it also says host does not exsist
Andy Sharrow
@dramageek
Jan 13 2017 20:05
@ryan_anglani_twitter It's a sort of generic message, and could be from a number of reasons. Earlier when you were sending it commands, was that directly in with the keyboard?
If so, type in ifconfig wlan0 and if it's on the network it'll give you the IP address. You can use that address from putty instead of the raspberrypi.local
Tim Mecklem
@tmecklem
Jan 13 2017 20:07
@melodyandrews I'm a little late to the conversation. If you were seeing gaps in the Medtronic cgm, is it still occurring? I've heard that a calibration will trick the timestamps into catching back up.
jaylagorio
@jaylagorio
Jan 13 2017 20:09
@dramageek I do G4 -> Share Receiver -> Pi -> NS
Share Receiver is connected to the Pi via USB
Tim Mecklem
@tmecklem
Jan 13 2017 20:09
I've got changes queued up for enlite decoding in openaps that should fix unexplained gaps and handle decoding lows and highs.
jaylagorio
@jaylagorio
Jan 13 2017 20:09
If an Internet connection isn't around it continues to work offline, I just can't monitor it in NS until I hit the Internet again
ejoe132
@ejoe132
Jan 13 2017 20:11
@ryan_anglani_twitter and your username is pi and password is raspberry, haha spend a bit of time thinking it was my NS one but wasnt
Andy Sharrow
@dramageek
Jan 13 2017 20:12
@jaylagorio I've heard that the Share USB port is rather fragile, and know that I'd end up snapping the thing off in my pockets. Hopefully this weekend I'll have time to give the latest dev oref0 a spin on my backup rig and see if I can get shareble working. That would cut out the phone at least.
I'm currently sporting the TicTac case, and love being able to fit it all in my pockets. Also, I think I heard that explorer>Share USB was still a WIP.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:15
@dramageek I put ifconfig wlan0 and I got the same message
@ejoe132 i have to get the putty part to work when i press open and that is not happening
Andy Sharrow
@dramageek
Jan 13 2017 20:17
@ryan_anglani_twitter Put the ifconfig wlan0 into the Pi, not into putty

It'll return something like:

root@openaps2:~# ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 90:b6:86:11:ad:96
          inet addr:192.168.1.191  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:405023 errors:0 dropped:0 overruns:0 frame:0
          TX packets:199562 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:293299755 (279.7 MiB)  TX bytes:20692030 (19.7 MiB)

The address you need is whatever is in the spot of "192.168.1.191" on mine.

jmcrawford
@jmcrawford
Jan 13 2017 20:19
@ryan_anglani_twitter If you're on a Windows laptop, raspberrypi.local only works if you've got iTunes installed. It should work be default if you are on a Mac or Linux computer. Name resolution (turning the raspberrypi.local into an IP address) is being done by the Bonjour system, which comes from iTunes. Without that, you'll likely need to connect directly to the IP address.
Dana Lewis
@danamlewis
Jan 13 2017 20:19
@dramageek fwiw, 2/3 people i talk to complain about missing g5 data. for some of your other qs - plugging share usb into explorer is doable, and there’s been work by a few people on xdrip for offline that I believe just needs to get documented...
Tim Street
@tim2000s
Jan 13 2017 20:20
@dramageek G5 via xDrip app seems to be more reliable than via the Dexcom app on iPhone, but I've a feeling that's iPhone Bluetooth stack related, and only based on a short period using xDrip on Android.
ejoe132
@ejoe132
Jan 13 2017 20:22
@ryan_anglani_twitter do you have the port set to 22, have ssh selected?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:23
@ejoe132 yes i do
@dramageek ok I'm doing that now
@jmcrawford i have itunes
ejoe132
@ejoe132
Jan 13 2017 20:31
@jmcrawford Are you saying If I want to access my pi with putty by just typing the address I need itunes? Cause my laptop can get connected real quick but was trying to make changes on it yesterday at school with a machine there and it couldnt connect, figured it was just a "small fish in a big pond" issue but maybe it was cause it didnt have itunes?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:34
@dramageek in my spot it have a 32 character thingy and its not working
jmcrawford
@jmcrawford
Jan 13 2017 20:35
You should always be able to connect to the IP address, but to connect to the hostname, you'd need iTunes. Also, I'm not sure what would happen if there were two pi's on the network with the same name
Andy Sharrow
@dramageek
Jan 13 2017 20:36
@ryan_anglani_twitter Hmm. IPv6 address? I'll deffer to someone else on what to do at this point.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:37
@dramageek it is fe80::1f88:a883:cbcf:fcac/64
j4cbo
@j4cbo
Jan 13 2017 20:38
Can OpenAPS connect from an Edison "directly" to a Dexcom G5 transmitter, like xDripG5 does?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:38
@dramageek in front of it is inet6 addr:
Scott Leibrand
@scottleibrand
Jan 13 2017 20:40
@ryan_anglani_twitter you might be able to connect with the IPv6 address, but you can also use the IPv4 address if you want something easier to read and type
Dana Lewis
@danamlewis
Jan 13 2017 20:40
@j4cbo we need someone to import the g5 stuff nate did originally for ios into linux.
j4cbo
@j4cbo
Jan 13 2017 20:41
I can do it if you need extra hands :)
Dana Lewis
@danamlewis
Jan 13 2017 20:41
please, please do it :) you’ll make even more friends here than you have already ;)
j4cbo
@j4cbo
Jan 13 2017 20:42
sweet :) I should have all my hardware in a week or so
Dana Lewis
@danamlewis
Jan 13 2017 20:42
awesome
Tim Street
@tim2000s
Jan 13 2017 20:42
@j4cbo You need to import the xDrip stuff from Android to Linux. What Nate did piggy backs on the Dexcom connection, so when the Dexcom app lost connection so did Loop.
Scott Leibrand
@scottleibrand
Jan 13 2017 20:42
if you want something to start from, openxshareble allows a rig to talk BLE to a G4 receiver. it isn't super reliable, though: it needs to be daemonized
Dana Lewis
@danamlewis
Jan 13 2017 20:43
^ that one too :D hashtag fix all the things
Scott Leibrand
@scottleibrand
Jan 13 2017 20:43
once daemonized, I suspect openxshareble would be a good place to put the ported code
j4cbo
@j4cbo
Jan 13 2017 20:44
cool
i'm getting a G5
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:45
@scottleibrand i don't see those
Tim Street
@tim2000s
Jan 13 2017 20:45
No point starting with the Loop stuff as it doesn't do the connectivity between iOS and the G5 transmitter.
j4cbo
@j4cbo
Jan 13 2017 20:46
oh, i was looking at https://github.com/LoopKit/xDripG5
Scott Leibrand
@scottleibrand
Jan 13 2017 20:46
@ryan_anglani_twitter where are you looking?
j4cbo
@j4cbo
Jan 13 2017 20:47
if i'm understanding it right the current usual setup is: G5 transmitter speaks BLE to the Dexcom receiver, and RPi (or whatever) talks to the Dexcom receiver over USB? and most people with Edison / Explorer Board setups use Enlite?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:48
i am looking at what popped up when i typed ifconfigwlan0 @scottleibrand
Dana Lewis
@danamlewis
Jan 13 2017 20:48
@j4cbo g5 usually goes to phone, most people don’t carry a receivr, but what you described is the usual g4 setup - or they pull data down from Nightscout. most people with edison/explorer boards are using whatever cgm they already had before - not necessarily enlite.
Pete Schwamb
@ps2
Jan 13 2017 20:49
Actually, Nate’s xDripG5 code is the right place to look for an example of how to talk to G5 over BLE, though it doesn’t implement the full G5 BLE comms (the dex app does the initial pairing, and calibration).
Dana Lewis
@danamlewis
Jan 13 2017 20:49
offline setup = either enlite, or a dexcom receiver (g4 or g5) plugged into rig (Pi, or explorer, or somethign else).
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:49
@jmcrawford should i update my iTunes?
Tim Street
@tim2000s
Jan 13 2017 20:49
@j4cbo quite a lot of use Nightscout download and are trying to set up the xDrip local system :;
;)
j4cbo
@j4cbo
Jan 13 2017 20:51
@danamlewis gotcha. so the dexcom BLE protocol is understood, but not implemented in OpenAPS right now
Tim Street
@tim2000s
Jan 13 2017 20:51
So if you are looking to implement full BLE comms, but via Linux, wouldn't xDrip make more sense @ps2?
Pete Schwamb
@ps2
Jan 13 2017 20:52
@tim2000s I don’t know what you mean when you say “xDrip”. Which code are you referring to?
Scott Leibrand
@scottleibrand
Jan 13 2017 20:52
@j4cbo correct. just a question of which implementation is best to port over to Linux.
Pete Schwamb
@ps2
Jan 13 2017 20:53
(unfortunately there is a lot of code with ‘xdrip’ in the name)
Scott Leibrand
@scottleibrand
Jan 13 2017 20:53
@ryan_anglani_twitter your ifconfig wlan0 output should looks something like:
edison@edison-rl ~ $ ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 78:4b:87:ab:23:54
          inet addr:192.168.29.29  Bcast:192.168.29.255  Mask:255.255.255.0
          inet6 addr: 2601:602:9801:31f9:7a4b:dead:beef:cafe/64 Scope:Global
          inet6 addr: fe80::7a4b:dead:beef:cafe/64 Scope:Link
Tim Street
@tim2000s
Jan 13 2017 20:53
I mean the xDrip app from Nightscout on android that works with G5 transmitter standalone.
Scott Leibrand
@scottleibrand
Jan 13 2017 20:53
the IPv4 address is the one that says inet addr:
Tim Street
@tim2000s
Jan 13 2017 20:54
(That I've been using for the past few days)
Pete Schwamb
@ps2
Jan 13 2017 20:54
oh, where is that?
j4cbo
@j4cbo
Jan 13 2017 20:54
i also want to try Loop, so i might write some code to make my Edison Explorer rig pretend to be a RileyLink, but one thing at a time...
Tim Street
@tim2000s
Jan 13 2017 20:55
Both xDrip and xDrip+ implement a G5 connection that includes full BLE with the transmitter. I think the code is available in xDrip repo
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 20:55
@scottleibrand it says inet6 addr
Tim Street
@tim2000s
Jan 13 2017 20:56
I think it's in a night scout repo now. Let me check.
Scott Leibrand
@scottleibrand
Jan 13 2017 20:56
@ryan_anglani_twitter so you only have a single one of those lines, and it's the inet6 addr: fe80:: line?
in that case, it means you're not getting a valid IP address, and therefore aren't connected to the Internet
Tim Street
@tim2000s
Jan 13 2017 20:59
@ps2 looks like that's right. It's xDrip-beta
Pete Schwamb
@ps2
Jan 13 2017 20:59
Ok, yes, it looks like there is G5 ble comms in the xdrip repo I pasted above, so that would be a good source too.
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 21:00
@scottleibrand you are correct!
Tim Street
@tim2000s
Jan 13 2017 21:00
:+1: @ps2
Pete Schwamb
@ps2
Jan 13 2017 21:00
xdrip may be more complete, since it has to do the full comms. Nate was the first to decode the g5 ble comm protocol, but it looks like others have taken it further on android.
j4cbo
@j4cbo
Jan 13 2017 21:01
nod. i'm imagining calibration would still go through the Dexcom app
for me, at least
Tim Street
@tim2000s
Jan 13 2017 21:02
No xDrip if you're using it calibrates
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 21:02
@scottleibrand ok i am connected now :)
and i have a better looking ip address
Chris Oattes
@cjo20
Jan 13 2017 21:03
yeah, the 192.168.0.* subnet is so pretty
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 21:05
@scottleibrand i now have a black box that popped up
so now i dont need the screen attached to the rpi3 correct?
Ryan anglani
@ryan_anglani_twitter
Jan 13 2017 21:14
i am not able to type the password :(
there is just a green box
i keep getting a fatal putty error that is popping up
ejoe132
@ejoe132
Jan 13 2017 21:26
@ryan_anglani_twitter Password stays invisible as a security measure, like windows stuff will do *for passwords
jaylagorio
@jaylagorio
Jan 13 2017 22:08
@dramageek I haven't had a problem with the Share port being fragile and I plug/unplug from the USB cable twice a day. It's not in my pocket though. Explorer -> Share USB works like a champ, it's Explorer -> ShareBLE that doesn't work or is super flakey. I've never had a successful BLE command, other report they have but it's not reliable.
Tictac case is cool!
PieterGit
@PieterGit
Jan 13 2017 22:24
@danamlewis : what do you mean with "An example of a too-sensitive one would be:" on {https://openaps.readthedocs.io/en/master/docs/walkthrough/phase-4/autotune.html . Would it not be clearer to advise people to use their own profile? i.e. cp settings/profile.json settings/pumpprofile.json to start with. What fields of the profile.json are mandatory for the (manual) autotune process?
Dana Lewis
@danamlewis
Jan 13 2017 22:27
people do start with their own profiles, but if for some reason they don’t have one that’s an example one. I think to your point the “too-sensitive” wording is unnecessary…what’s your thoughts on providing an example like that vs. telling people to copy the pump profile from their rig?
I can just edit it to not say “too-sensitive” and make it more clear that it’s an example, or we can remove the example. preference?
C-Ville
@C-Ville
Jan 13 2017 22:30
I started using the dev setup script on an edison rig yesterday. I activated everything including autotune. currently my pumpprofile.json gets filled with data but my profile.json stays empty, which then fails to be available for iob.json and following loop reports. Is this a commone behaviour?
Scott Leibrand
@scottleibrand
Jan 13 2017 22:38
@c-ville I thought I fixed that in the latest dev. What happens when you run the profile.json report manually?
C-Ville
@C-Ville
Jan 13 2017 22:41
@scottleibrand I will reboot my edison, I gave up yesterday and did not restart today. One gets lazy if a running rig is around :-)
jmcrawford
@jmcrawford
Jan 13 2017 22:45
@ryan_anglani_twitter I don't think the version matters - but doesn't @pple make you update itunes pretty much every time you use it?
C-Ville
@C-Ville
Jan 13 2017 22:57
@scottleibrand I will also need to stop my RPI Rig. The radio of the TI Stick is way to strong, so I am back
edison@miniaps:~/APS$ openaps report invoke settings/profile.json
get-profile://text/shell/settings/profile.json
/usr/local/bin/oref0-get-profile pump_settings.json bg_targets.json insulin_sensitivities.json basal_profile.json [preferences.json] [<carb_ratios.json>] [<temptargets.json>] [--model model.json]

Options:
  --model, -m          Pump model response  [default: false]
  --help               Show help  [boolean]
  --exportDefaults     Show default preference values  [default: false]
  --updatePreferences  Check for any keys missing from current prefs and add from defaults  [default: false]

Unknown argument: autotune
reporting settings/profile.json
edison@miniaps:~/APS$
Scott Leibrand
@scottleibrand
Jan 13 2017 22:59
@C-Ville looks like you need to npm run global-install from ~/src/oref0 to fully install the version of oref0 that supports autotune
C-Ville
@C-Ville
Jan 13 2017 23:00
@scottleibrand thanks will do, i thought I did everything thats described in the docs, maybe not so
Scott Leibrand
@scottleibrand
Jan 13 2017 23:02
I don't think the docs fully cover how to upgrade to the latest dev, since that is a moving target
this isn't a problem when using master and package installs
C-Ville
@C-Ville
Jan 13 2017 23:08
@scottleibrand I guess more attention and not enabling autotune could have saved me too. I am currently after the xdrip setup more than the autotune
C-Ville
@C-Ville
Jan 13 2017 23:15
@scottleibrand thanks seems to be running nicely now