These are chat archives for nightscout/intend-to-bolus

16th
May 2017
live4sw
@live4sw
May 16 2017 00:32
Re: cutting the Explorer board antenna - are we supposed to cut fully through the board, or just through the green and cut into the copper?
(I know it's not necessary to cut at all, but I have been struggling with range issues and decided to do it - I cut into it but the knife would not go all the way through, it slipped a bit but cut through the green and dug pretty well into the copper)
Scott Leibrand
@scottleibrand
May 16 2017 00:36
@JELCRAWFORD I'm surprised to hear you had much in the way of overreaction recovering from the compression low. usually those bounce up so fast that the high temp gets cancelled after 5-15 minutes, before it has a chance to get much insulin in
I wonder if that's related to your really high overnight maxSafeBasal?
JELCRAWFORD
@JELCRAWFORD
May 16 2017 00:39
Nope. Maxsafebasal is not BLU high between
Aarrg. Only high between 6-11pm.
I thing because he was already trending low and then I went back to sleep without thinking to set a temp target, he dropped to 3.8
So not really low, but then sat there at a zero temp for a long time... despite small correction attempts. An annoyance at 3am that
Didn't stop until we gave a latger correction that brought him up to the 7's....
Sorry. Weird keyboard troubles here.
fidoman
@efidoman
May 16 2017 00:48
5-15-2017 8-45-23 PM.png
@danamlewis - above is a day where it seemed to put me on a bit of a roller coaster ride ....
JELCRAWFORD
@JELCRAWFORD
May 16 2017 00:48
@scottleibrand - I think the fact that DS goes from high insulin needs/resistance to low with very little time passing makes him more vulnerable to lows overnight. It is impossible for Openaps to soften a drop when he has little to no insulin as basal - it is not unusual for him to run a zero temp for hours in the after midnight period. This combined with the need for big correction just hours earlier mean that the tail effect of the insulin causes a low. This was true before Openaps and is very muted compared to what we had. we don't have any idea why except to presume that for some reason, after midnight, his pancreas decides its a good time to be 'helpful' to whatever degree it has left...
Dana Lewis
@danamlewis
May 16 2017 00:51
@ericfeibelman it would be helpful to see some logs. Also, do you use eating soon before meals?
fidoman
@efidoman
May 16 2017 00:54
@danamlewis - I do try to use eating soon whenever I can. I can pull some logs for that day. What logfile would be helpful
JELCRAWFORD
@JELCRAWFORD
May 16 2017 00:59
Screen Shot 2017-05-15 at 6.58.55 PM.png
Screen Shot 2017-05-15 at 6.57.36 PM.png
Saturday night into Sunday morning... Of course high temporary target is not really helpful when temped out already. The little blip of insulin delivery dropped him fully into low - perhaps he have gone there anyhow... probably.
Brian Rabinovitz
@bdr1177
May 16 2017 01:02
I'm suddenly getting this error. Any ideas?
Starting pump-loop at Mon May 15 20:51:04 EDT 2017: Traceback (most recent call last): File "/usr/local/bin/mmeowlink-any-pump-comms.py", line 15, in <module> app.run(None) File "/usr/local/lib/python2.7/dist-packages/decocare/helpers/cli.py", line 113, in run self.prelude(args) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/cli/any_pump_comms_app.py", line 28, in prelude super(AnyPumpCommsApp, self).prelude(args) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/cli/base_mmeowlink_app.py", line 26, in prelude self.link = link = LinkBuilder().build(args.radio_type, port) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/link_builder.py", line 16, in build return SubgRfspyLink(port) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 55, in __init__ self.open() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_interface.py", line 28, in open self.check_setup() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 72, in check_setup self.serial_rf_spy.sync() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_rf_spy.py", line 121, in sync raise CommsException("Could not get subg_rfspy state or version. Have you got the right port/device and radio_type?") mmeowlink.exceptions.CommsException: Could not get subg_rfspy state or version. Have you got the right port/device and radio_type? mmtune: monitor/mmtune.json raised Could not get subg_rfspy state or version. Have you got the right port/device and radio_type? pump://JSON/mmtune/monitor/mmtune.json Traceback (most recent call last): File "/usr/local/bin/openaps-report", line 82, in <module> app( ) File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 51, in __call__ self.run(self.args) File "/usr/local/bin/openaps-report", line 75, in run output = app(args, self) File "/usr/local/lib/python2.7/dist-packages/openaps/cli/subcommand.py", line 52, in __call__ return self.method.main(args, app) File "/usr/local/lib/python2.7/dist-packages/openaps/reports/invoke.py", line 40, in main output = task.method(args, app) File "/usr/local/lib/python2.7/dist-packages/openaps/uses/use.py", line 44, in __call__ self.before_main(args, app) File "/usr/local/lib/python2.7/dist-packages/openaps/vendors/medtronic.py", line 62, in before_main self.setup_medtronic( ) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/mmeowlink.py", line 92, in setup_medtronic setup_medtronic_link(self) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/mmeowlink.py", line 75, in setup_medtronic_link link = builder.build(radio_type, port) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/link_builder.py", line 16, in build return SubgRfspyLink(port) File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 55, in __init__ self.open() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_interface.py", line 28, in open self.check_setup() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 72, in check_setup self.serial_rf_spy.sync() File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_rf_spy.py", line 121, in sync raise CommsException("Could not get subg_rfspy state or version. Have you got the right port/device and radio_type?") mmeowlink.exceptions.CommsException: Could not get subg_rfspy state or version. Have you got the right port/device and radio_type? Usage: grep [OPTION]... PATTERN [FILE]... Try 'grep --help' for more information. Listening: ................................
Bob Duerr
@Duer0049
May 16 2017 01:03
Hi All, anyone run into the issue where you connected to the rig by SSH and when you try and reboot, it immediately closes the server connection?
Brian Rabinovitz
@bdr1177
May 16 2017 01:38
So I deleted my openaps directory and reran the setup script, but I'm still getting the same error as above. Any ideas?
andyhandy
@andyhandy
May 16 2017 02:14
I have an Edison with explorer board and consistently have issues with the rig not connecting to the iPhone by Bluetooth when moving out of a known WiFi network (eg when my son leaves home to go to school). If I do a hard reboot of the rig it manages to find the connection. Anyone have any suggestions? Thanks!
Bob Duerr
@Duer0049
May 16 2017 02:16
Hi all Again, I am having an issue where the my rig won't stay connected to the pump, the rig is on wifi, I verified that and the model number is correct, it will connect for a little bit after a reboot, but it doesn't stay connected. This is the looping error I get: "916.636", 0, -99 Starting pump-loop at Mon May 15 20:56:12 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old pumphistory:
Error, retrying
Starting pump-loop at Mon May 15 20:57:20 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old pumphistory:
Error, retrying
Starting pump-loop at Mon May 15 20:58:27 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old pumphistory:
Error, retrying
Starting pump-loop at Mon May 15 20:59:37 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old pumphistory:
Error, retrying
Starting pump-loop at Mon May 15 21:00:44 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old pumphistory:
Error, retrying
Martin Haeberli
@mhaeberli
May 16 2017 02:18
wlan is ‘flapping’ … [ 954.685486] wl_bss_connect_done succeeded with 88:ad:43:05:f8:88
suggestions?
Martin Haeberli
@mhaeberli
May 16 2017 02:24
also, how do I get it NOT to spit out that kind of message to the console and just keep them quietly in a log file
Scott Leibrand
@scottleibrand
May 16 2017 02:27
@Duer0049 your rig isn't seeing your pump: the -99 means it never got a response to mmtune at an of the frequencies it tried, so it defaulted to the midpoint of 916.636 MHz. Is this a NA pump, or WW?
Bob Duerr
@Duer0049
May 16 2017 02:28
NA
Scott Leibrand
@scottleibrand
May 16 2017 02:28
any Linux computer will terminate all ssh connections when you reboot. you can log back in when it boots back up.
have you gotten good signal in the past with this rig and pump?
Bob Duerr
@Duer0049
May 16 2017 02:28
Yes
It was working 2 hours ago
Scott Leibrand
@scottleibrand
May 16 2017 02:29
is the pump battery level good?
Bob Duerr
@Duer0049
May 16 2017 02:29
It has not alarmed, but it is on it's last bar
Scott Leibrand
@scottleibrand
May 16 2017 02:30
@ericfeibelman it looks like your roller coaster is happening a bit too fast to be solely due to whatever OpenAPS is doing. did you have unannounced rescue carbs at 11am?
@Duer0049 does the backlight come on when you hit the down arrow?
Bob Duerr
@Duer0049
May 16 2017 02:30
Yes
Scott Leibrand
@scottleibrand
May 16 2017 02:31
have you tried putting the rig just inches from the pump to see if it can mmtune there?
@ericfeibelman have you run autotune yet? one possibility is your ISF might be too strong (low)...
Bob Duerr
@Duer0049
May 16 2017 02:31
One sec, changing the battery quick
Scott Leibrand
@scottleibrand
May 16 2017 02:33
some people notice the pumps start to get flaky on RF comms even before they drop into low power mode and shut it off completely
Scott Leibrand
@scottleibrand
May 16 2017 02:40
@bdr1177 you might try reseating your Edison onto your Explorer board. what do the two LEDs next to the microUSB ports do when you mmtune? they should blink and then go off. if they stay on, that might indicate you need to re-flash the cc1110 with ccprog.
Bob Duerr
@Duer0049
May 16 2017 02:45
@scottleibrand Changed the battery, got communication back, now I have this error: Starting pump-loop at Mon May 15 21:41:13 CDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Profile less than 60m old
glucose.json newer than temp_basal.json
Temp refreshed
Temp duration 27m or more
glucose.json newer than pumphistory: Refreshed pumphistory
Could not parse input data: [TypeError: Cannot read property 'date' of undefined]
determine-basal://text/shell/enact/suggested.json
reporting enact/suggested.json
{"bg":79,"temp":"absolute","snoozeBG":73,"recieved":true,"predBGs":{"IOB":[79,77,76,75,74,73,73,73,72,72,72,72,72]},"rate":0,"reason":"COB: undefined, Dev: 1, BGI: -1.78, ISF: 24, Target: 100; Eventual BG 73 < 80, setting -2.9U/hr","eventualBG":73,"timestamp":"2017-05-15T21:39:57.362128","duration":30,"tick":"+1","IOB":0.281}
Settings less than 10m old
Pumphistory-24 less than 20m old
Completed pump-loop at Mon May 15 21:42:31 CDT 2017
Scott Leibrand
@scottleibrand
May 16 2017 02:48
does that clear up on the next run?
it looks like it's setting a zero temp properly
Bob Duerr
@Duer0049
May 16 2017 02:50
Yes, it is cleared up on the next one, but seems to pop back up every 3rd loop or so
Scott Leibrand
@scottleibrand
May 16 2017 02:51
seems like your glucose data might be getting overwritten sometimes. what CGM source/method are you using? xdrip?
Bob Duerr
@Duer0049
May 16 2017 02:51
Yes
Scott Leibrand
@scottleibrand
May 16 2017 02:52
ok, I think that's a known issue, but I'm not sure the status of the fix. perhaps someone else who uses xdrip can comment
I've seen people talking about how to fix it manually, but not sure if it's been fixed in oref0 dev or not
Bob Duerr
@Duer0049
May 16 2017 02:52
Ok, we are back to looping again, and the status is up on NS, thank you for your help
Scott Leibrand
@scottleibrand
May 16 2017 02:52
:+1:
Martin Haeberli
@mhaeberli
May 16 2017 03:08
trying to do the bluetooth thing
sudo bt-pan client 90:60:F1:B2:E1:BB
Traceback (most recent call last):
  File "/usr/local/bin/bt-pan", line 228, in <module>
    if __name__ == '__main__': sys.exit(main())
  File "/usr/local/bin/bt-pan", line 196, in main
    try: iface = net.Connect(opts.uuid)
  File "/usr/lib/python2.7/dist-packages/dbus/proxies.py", line 145, in __call__
    **keywords)
  File "/usr/lib/python2.7/dist-packages/dbus/connection.py", line 651, in call_blocking
    message, timeout)
dbus.exceptions.DBusException: org.bluez.Error.Failed: Input/output error
Martin Haeberli
@mhaeberli
May 16 2017 03:17
now upgraded to
sudo bt-pan client 98:4F:EE:02:F5:D0
Traceback (most recent call last):
  File "/usr/local/bin/bt-pan", line 228, in <module>
    if __name__ == '__main__': sys.exit(main())
  File "/usr/local/bin/bt-pan", line 188, in main
    dev_remote = find_device(opts.remote_addr, devs.values()[0])
  File "/usr/local/bin/bt-pan", line 53, in find_device
    return find_device_in_objects(get_manager().GetManagedObjects(), device_address, adapter_pattern)
  File "/usr/local/bin/bt-pan", line 68, in find_device_in_objects
    raise BTError('Bluetooth device not found')
__main__.BTError: Bluetooth device not found
Martin Haeberli
@mhaeberli
May 16 2017 03:25
ok - fixed by a few reboots
next question - what if I need to CHANGE what bluetooth device I’m paired with?
Matthew Williams
@mwilliams
May 16 2017 03:27
@scottleibrand Goooood evening, thanks for the tip on openaps first-upload, that kicked NS into gear running on a fresh instance of the def branch and the mdt-cgm brand of oref0 - all looking great, so far
Helene Brashear
@sillystring13
May 16 2017 03:28
@mhaeberli the string "98:4F:EE:02:F5:D0" is the address for your bluetooth device and then "bt-pan client" creates the connection, so for another device, you would run "bt-pan client" with the address for the new bluetooth device
Martin Haeberli
@mhaeberli
May 16 2017 03:29
@sillystring13 great, thanks; so I can ‘just’ pair to the new device using bluetoothctl or whatever, then re-run bt-pan client etc (assuming I’m disconnected in between)
Helene Brashear
@sillystring13
May 16 2017 03:32
@mhaeberli yup and you can disconnect with -d like "bt-pan client -d 98:4F:EE:02:F5:D0" - there's some more info here https://openaps.readthedocs.io/en/master/docs/walkthrough/phase-4/bluetooth-tethering-edison.html
Martin Haeberli
@mhaeberli
May 16 2017 03:36
:+1:
katie disimone
@Kdisimone
May 16 2017 03:46
@mhaeberli I do believe though that there's a crontab line you'd need to add too. Oref0-online uses your phone's bt mac in the crontab
Martin Haeberli
@mhaeberli
May 16 2017 03:47
@Kdisimone thx
katie disimone
@Kdisimone
May 16 2017 03:47
So you could pair multiple devices easily, but would need to add crontab separately...and if you want to forcibly push the rig to one or the other, I suppose you may have to just turn BT off temporarily on the one you don't want?
porkupan
@porkupan
May 16 2017 03:48
@scottleibrand Do I need to do anything special to get the USB OTG connection to Dexcom G4 going (Explorer Board)? I seem to be always getting AttributeError: 'NoneType' object has no attribute 'iter_records'
katie disimone
@Kdisimone
May 16 2017 03:50
@porkupan make sure you have a version 1.2 explorer board (it says that one the board). Make sure your OTG cable is plugged into the explorer board (not the receiver). Make sure you chose G4-upload for the CGM type
porkupan
@porkupan
May 16 2017 03:53
@Kdisimone How do I choose G4-upload for the CGM type?
katie disimone
@Kdisimone
May 16 2017 03:54
@porkupan Ah, yeah…G4-upload is on dev branch. If you used master branch, did you choose G4?
porkupan
@porkupan
May 16 2017 03:55
@Kdisimone Yes, I did. But it's been a couple of months now. It's just my son's phone broke, so in the meanwhile we need to figure out how to upload CGM data.
katie disimone
@Kdisimone
May 16 2017 03:56

It should be able to loop with CGM plugged in, but you may not get NS views unless in wifi then.

also, make sure the OTG cable is plugged into the OTG port on explorer board

Dana Lewis
@danamlewis
May 16 2017 04:04
Thx for bookmarking as issue @Kdisimone
porkupan
@porkupan
May 16 2017 04:09
It's plugged into the OTG port, but doesn't seem to work. Not sure if it's Explorer v. 1.2 (I don't see anything like that printed on the board).
[ 1900.198504] pmic_ccsm pmic_ccsm: USB VBUS Detected. Notifying OTG driver
[ 1902.668757] dwc3-device dwc3-device.1: device suspended; notify OTG
[ 1958.037081] pmic_ccsm pmic_ccsm: USB ID Detected. Notifying OTG driver
Trying to run:
# openaps use cgm iter_glucose 1
Traceback (most recent call last):
  File "/usr/local/bin/openaps-use", line 63, in <module>
    app( )
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 51, in __call__
    self.run(self.args)
  File "/usr/local/bin/openaps-use", line 57, in run
    output = app(args, self)
  File "/usr/local/lib/python2.7/dist-packages/openaps/uses/__init__.py", line 92, in __call__
    return self.method.selected(args)(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/uses/__init__.py", line 31, in __call__
    return self.method(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/uses/use.py", line 45, in __call__
    output = self.main(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/vendors/dexcom.py", line 418, in main
    candidates = itertools.takewhile(self.comparison, self.dexcom.iter_records(self.RECORD_TYPE))
AttributeError: 'NoneType' object has no attribute 'iter_records'
Jason Wittmer
@jbwittmer
May 16 2017 04:19
OK I give up and need some help . I've been working at trying to set up a test rig for SMB. Have tried to follow all the directions I've gleaned. Using latest dev. Have enabled the 3 SMB categories in preferences.json. Installed with -microbolus flag using script. Getting the following error message. Starting supermicrobolus pump-loop at Mon May 15 23:16:34 CDT 2017 with 16 second wait_for_silence:
Waiting up to 4 minutes for new BG: ls: cannot access monitor/pump_loop_completed: No such file or directory
Radio ok. Listening: .No pump comms detected from other rigs
Preflight OK. Profile less than 60m old. find: `monitor/pump_loop_completed': No such file or directory
pump_loop_completed less than 5m ago. RefreshRemoved duplicate bolus/carb entries:3
ed pumphistory
pumphistory.json: "TempBasalDuration 2017-05-15T22:54:48 head[2], body[0] op[0x16]"
Checking pump clock: "2017-05-15T23:16:13-05:00" is within 1m of current time: Mon May 15 23:17:19 CDT 2017
Error, retrying
Sleeping 2;
Any suggestions what to do next?
Scott Leibrand
@scottleibrand
May 16 2017 04:28
Checking pump clock: "2017-05-15T23:16:13-05:00" is within 1m of current time: Mon May 15 23:17:19 CDT 2017
Error, retrying
katie disimone
@Kdisimone
May 16 2017 04:28
Your pump time is 66 seconds slower than the rig time…and they have to be within 60 seconds
Scott Leibrand
@scottleibrand
May 16 2017 04:28
What does that tell you?
katie disimone
@Kdisimone
May 16 2017 04:28
Ah, i gave away the punch line
Scott Leibrand
@scottleibrand
May 16 2017 04:29
@porkupan you can use lsusb to see if the CGM is working over OTG. You should see three lines, not the -99
Jason Wittmer
@jbwittmer
May 16 2017 04:30
OK thx. I think. I'll see if I can fix that
Scott Leibrand
@scottleibrand
May 16 2017 04:30
Which reminds me we need to try to have oref0-pump-loop fix that automatically.
@porkupan Are you using an external USB battery on the UART port? Does the Dex receiver's charging icon come on?
porkupan
@porkupan
May 16 2017 04:33
@scottleibrand here is what lsusb puts out:
# lsusb
unable to initialize libusb: -99
root@OpenAPS:~#
Yes, the charging icon comes up on the Receiver.
Scott Leibrand
@scottleibrand
May 16 2017 04:34
So no go. You have a hardware issue to fix.
Could be the microUSB OTG cable, or power, or your Explorer board being old and flaky. Do you have a newish 1.2 one anywhere?
porkupan
@porkupan
May 16 2017 04:35
Any idea what kind of hardware issue?
My board is the first production build
Scott Leibrand
@scottleibrand
May 16 2017 04:35
The previous versions had a design flaw that made OTG unreliable.
There is a trace cut you can do to work around that.
porkupan
@porkupan
May 16 2017 04:36
Oh. Well, could be it then.
Scott Leibrand
@scottleibrand
May 16 2017 04:36
See the closed issue on the EB repo
porkupan
@porkupan
May 16 2017 04:36
Do you have instructions for a trace cut?
Ok, thanks.
Jason Wittmer
@jbwittmer
May 16 2017 04:40
@scottleibrand and @Kdisimone Thanks for the (simple) fix. Don't know how I looked past that for the last two hours! Looping on SMB test rig now. Unfortunately son now lowish and asleep, so testing will need to wait until later but at least it's running now. By the way, @scottleibrand , tell me where to log this: I'm using an older soldered rig to test and NOT using autotune or UAM. I had to install jq manually. I assume that's something that will need to be updated in scripted install before going to master. Thanks.
katie disimone
@Kdisimone
May 16 2017 04:42
@jbwittmer I had that problem on my first rig’s update to dev SMB branch too. It did solve when I deleted the src and myopenaps directories. Didn’t really add that much time to the process…but the jq did install even without autotune selected that way
Jason Wittmer
@jbwittmer
May 16 2017 04:43
Nice to know I'm not the only one with the strange problems to fix
Maybe not strange. Unanticipated
katie disimone
@Kdisimone
May 16 2017 04:48

thoughts on why new rig setup isn’t grabbing?

May 15 21:47:01 caraedison pump-loop.log:  {"carbs":0,"mealCOB":0,"reason":"carb_ratio undefined out of bounds"}
May 15 21:47:01 caraedison pump-loop.log:  {"ratio":1,"reason":"not enough glucose data to calculate autosens"}
May 15 21:47:01 caraedison pump-loop.log:  []
May 15 21:47:01 caraedison pump-loop.log:  {"delta":-1,"glucose":124,"short_avgdelta":1.28,"long_avgdelta":0.95}
May 15 21:47:01 caraedison pump-loop.log:  {"duration":0,"rate":0,"temp":"absolute"}
May 15 21:47:01 caraedison pump-loop.log:  Error: could not get current basal rate
May 15 21:47:03 caraedison pump-loop.log:  determine-basal://text/shell/enact/suggested.json

looks like it’s missing a whole line there...

Scott Leibrand
@scottleibrand
May 16 2017 04:56
@jbwittmer oref0 issue please with the combination of things you're running in oref0-setup so we can make sure we install jq in that situation too.
Jason Wittmer
@jbwittmer
May 16 2017 04:57
OK Will do.
Scott Leibrand
@scottleibrand
May 16 2017 04:57
@Kdisimone could be a transient bad read from the pump? Remove the profile.json and make it refresh it, or just wait and see if it resolves itself?
katie disimone
@Kdisimone
May 16 2017 04:58
good idea thanks
katie disimone
@Kdisimone
May 16 2017 05:21
@scottleibrand yup…profile.json was a bad read
tynbendad
@tynbendad
May 16 2017 05:22
any idea why i'm getting this git error on every command? stopped looping also (oldpumphistory failing)
root@benaps:~/myopenaps# openaps alias show pump-loop
pump-loop ! bash -c "sleep $[ ( $RANDOM / 2048 ) ]s; until(echo Starting pump-loop at $(date): && openaps wait-for-silence && openaps refresh-old-pumphistory && openaps refresh-old-pumphistory-24h && openaps refresh-old-profile && openaps refresh-temp-and-enact && openaps refresh-pumphistory-and-enact && openaps refresh-profile && openaps refresh-pumphistory-24h && echo Completed pump-loop at $(date) && echo); do echo Error, retrying && [[ $RANDOM > 25000 ]] && openaps wait-for-long-silence && openaps mmtune; sleep 5; done"
Traceback (most recent call last):
  File "/usr/local/bin/openaps-alias", line 37, in <module>
    app( )
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 52, in __call__
    self.epilog( )
  File "/usr/local/bin/openaps-alias", line 27, in epilog
    super(AliasApp, self).epilog( )
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 75, in epilog
    self.create_git_commit( )
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 89, in create_git_commit
    self.repo.git.add([diff.b_path], write_extension_data=False)
  File "/usr/local/lib/python2.7/dist-packages/git/cmd.py", line 425, in <lambda>
    return lambda *args, **kwargs: self._call_process(name, *args, **kwargs)
  File "/usr/local/lib/python2.7/dist-packages/git/cmd.py", line 877, in _call_process
    return self.execute(call, **exec_kwargs)
  File "/usr/local/lib/python2.7/dist-packages/git/cmd.py", line 688, in execute
    raise GitCommandError(command, status, stderr_value, stdout_value)
git.exc.GitCommandError: Cmd('git') failed due to: exit code(128)
  cmdline: git add myopenaps/enact/suggested.json
  stderr: 'fatal: pathspec 'myopenaps/enact/suggested.json' did not match any files'
root@benaps:~/myopenaps# ls -l ~/myopenaps/enact/suggested.json
-rw-r--r-- 1 root root 412 May 15 21:55 /root/myopenaps/enact/suggested.json
Brian Rabinovitz
@bdr1177
May 16 2017 05:44
@scottleibrand The two small LEDs are staying on continuously. What is flash the cc1110 with ccprog? Does that mean reflash the Edison, or something different?
Martin Haeberli
@mhaeberli
May 16 2017 05:50
@bdr1177 suggest you look at the "troubleshooting" page. In my experience, at least some new explorer boards need to be programmed "flashed " w cc prog before they can talk to a pump. Troubleshooting guide has directions on that
It is NOT reflash the Edison. "It's turtles all the way down". The radio on the explorer board that talks to the pump has its own, small, flash memory
Brian Rabinovitz
@bdr1177
May 16 2017 05:53
@mhaeberli Ok. Does it matter that this isn't a new explorer board? It has been up and running for months.
Martin Haeberli
@mhaeberli
May 16 2017 06:02
Arguably shouldn't be needed if board worked with pump before
How fast does oref0 age out cob? What can I do if I deem cob estimate much too highly; imho w trend it should low temp but it is not
Brian Rabinovitz
@bdr1177
May 16 2017 06:06
@mhaeberli Well, I guess I'll try anyway since nothing else seems to work.
Grant
@Bender_Fry_twitter
May 16 2017 06:21
Hi all I'm new to the OpenAPS scene and set up an edison device last week that has been working great but I have run into one issue in that Nightscout consistently reports a higher battery percentage for the edison than what it has as it will die after about 12-14 hours of use while nightscout still shows 40% battery remaining. Any tips on how to get it to report the percentage accurately?
Brian Rabinovitz
@bdr1177
May 16 2017 06:24
@scottleibrand @mhaeberli Thanks for the suggestion. Reflashing the radio worked. I wonder if this means that the radio on the explorer board is going bad, or if it's just an isolated error.
tynbendad
@tynbendad
May 16 2017 07:18
i tried everything, pump battery, proximity, rebooting rig, reseating edison, but they didn't help. finally reinstalled oref0 (0.4.2) and re-set-it-up... working again, schwew. not sure why that happened - is it something that happens a lot?
Martin Haeberli
@mhaeberli
May 16 2017 08:20
Ok - again getting BG out of date. Sometimes fixed temporarily via invoking openaps ns-loop. Sometimes fixes near-permanently that way. Sometimes restart fixes, still looking for root cause
samihusseingit
@samihusseingit
May 16 2017 09:36
I need advice on regards to auto-tune for anyone who is an expert on this
I am currently acting as an auto-tune..I look at yesterdays report of my son, and modify his profile (today slightly), yes I know we were supposed to wait 1 week to see patterns but I do this anyways :)
My question...if I do this...I am guessing auto-tune will get lost? Since I have just modified the profile? and it no longer matches yesterdays details?
do I have to leave the profile untouched for a week before auto-tune can do its thing?
:) thanks
Brian Rabinovitz
@bdr1177
May 16 2017 10:17
@samihusseingit There is a separate Gitter channel for autotune issues (openaps/autotune). You might try asking your question there.
samihusseingit
@samihusseingit
May 16 2017 10:22
ok, thank you :)
fidoman
@efidoman
May 16 2017 10:23
@danamlewis @scottleibrand - I ran the autotune procedures last night, so let me test a few more days before we troubleshoot further. And yes, I did have unnannounced rescue carbs at 11am & probably too many carbs. I will be diligent in my testing over the next few days to put in every carb intake.

@danamlewis @scottleibrand - This is what autotune gives me. I had run something a couple of weeks ago and adjusted my basal profiles accordingly, so it looks like I may have already done the autotune before because the numbers match what is recommended.

Parameter | Current | Autotune

ISF | 46.000 | 46.000
CSF | n/a | 0.000
Carb Ratio | 12.000 | 12.000
00:00 | 0.650 | 0.650
04:00 | 0.800 | 0.800
10:00 | 0.650 | 0.650
15:00 | 0.800 | 0.800
18:00 | 0.650 | 0.650

brandonschmidt
@brandonschmidt
May 16 2017 12:18
Hi, I'm in the process of obtaining the necessary hardware for OpenAPS. I see that there's a maximum firmware requirement for the Medtronic 723, but I don't see one for the 722 or below. Does this mean that any firmware should work with the Medtronic models prior to 723?
cameronrenwick
@cameronrenwick
May 16 2017 12:26
Abrand
@brandonschmidt you've seen this https://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-0/hardware/pump.html correct? Some pumps (512/712) will work but need additions for looping
Paul Dickens
@thebookins
May 16 2017 12:36
I'm having no end of trouble getting the G5 to pair with the edison (working towards pulling glucose locally on edison) and am pretty sure now that is has something to do with the BT security level in the linux kernel (see https://www.spinics.net/lists/linux-bluetooth/msg69237.html). Newer versions of the kernel have this patch which may solve my issues. How hard would it be to either install this patch or a newer version of the kernel? Hoping @esialb might be able to help :smile:
Matthias
@ceben80
May 16 2017 13:22
@brandonschmidt due to restrictions of pump commands beiing performed when looping, a x12 pump is not really recommended, if you have a chance to get a x22 pump for instance, will be better
fidoman
@efidoman
May 16 2017 13:24
Can you list what commands are restricted on the x12 pumps that can't be overridden by the static json files?
fidoman
@efidoman
May 16 2017 13:30
FYI - it seems that ebay is removing all insulin pumps that were for sale - I just bought two of them and paid via paypal and they were removed also.
Martin Haeberli
@mhaeberli
May 16 2017 13:32
Bummer!
brandonschmidt
@brandonschmidt
May 16 2017 13:35
@cameronrenwick, yes, that page was the impetus for my question. I just wanted to verify the only the 523 and 723 were subject to the maximum firmware limitations.
@ceben80, gotcha, thanks.
katie disimone
@Kdisimone
May 16 2017 13:41
@tynbendad not super often. I have three rigs and nearly five months. I'd say it's happened about three times that I've found it easier to just wipe and redo a loop installation.
fidoman
@efidoman
May 16 2017 13:55
can you do SMB with an x12 pump and following the instructions for static json's?
Dana Lewis
@danamlewis
May 16 2017 14:37
@ericfeibelman should be able to in theory; but haven't had anyone with an x12 a) fix the setup instructions for x12s or b ) try SMB, so not confirmed
fidoman
@efidoman
May 16 2017 14:39
@danamlewis - OK I have it as a backup pump so maybe I'll test it out at some point in the near future.
5-16-2017 10-37-34 AM.png
@scottleibrand @danamlewis - I did a test of SMB this morning and really tried to push it by bolusing much less than the bolus wizard suggested and SMB did not overcompensate. I'll continue to do tests like this but will bolus closer to the suggested amounts.
Dana Lewis
@danamlewis
May 16 2017 14:46
@ericfeibelman please do. I've begged the last handful of people who come through with x12s to update the docs and no one has, so will be super helpful
fidoman
@efidoman
May 16 2017 14:47
@danamlewis - OK, my 512 should arrive in a week or two
@danamlewis @scottleibrand Here's a better screenshot that shows that SMB is doing what I would expect it to do ...
image.png
Dana Lewis
@danamlewis
May 16 2017 14:48
:+1:
Btw - what are your targets?
fidoman
@efidoman
May 16 2017 14:50
Target for this time of the day is 90, so SMB seems to be mathematically perfect in this single case
Dana Lewis
@danamlewis
May 16 2017 14:51
90-90, or a range?
fidoman
@efidoman
May 16 2017 14:55
It is a range, what's the quickest way I can find that? I'm currently ssh'd into the rig or is that on my pump?
Dana Lewis
@danamlewis
May 16 2017 14:56
Pump, bolus wizard
Review bolus wizard settings
fidoman
@efidoman
May 16 2017 14:57
90 to 100 at this time of day. Probably a bit too tight.
Dana Lewis
@danamlewis
May 16 2017 14:57
No, that's reasonable for closed loop
Wider tends to cause confusion (why isn't it doing anything?!). Just wanted to check since that's a common source of confusion
tynbendad
@tynbendad
May 16 2017 15:23
@Kdisimone thx, I guess it's easy/quick enough I could just make it my go to thing after checking all the easy stuff ;)
Scott Leibrand
@scottleibrand
May 16 2017 15:30
@tynbendad if you have persistent git errors you can also rm -rf .git and let oref0-reset-git recreate it.
Matthew Williams
@mwilliams
May 16 2017 15:33
Hey hey everyone - looking to kick off SMB on my rig, I've flipped all the bits to true, though not seeing any just yet curious if remainingCarbsCap needs to get bumped? Is the SMB Github issue worth a full read?
Scott Leibrand
@scottleibrand
May 16 2017 15:34
Yes please read the whole thing for familiarity.
Matthew Williams
@mwilliams
May 16 2017 15:34
will do, started last night but midnight was quickly approaching as much as I wanted to see some SMB's in NS overnight :)
Scott Leibrand
@scottleibrand
May 16 2017 15:34
remainingCarbsCap will allow it to SMB if you enter carbs before bolusing for (all of) them.
Matthew Williams
@mwilliams
May 16 2017 15:34
ack
Scott Leibrand
@scottleibrand
May 16 2017 15:35
@ericfeibelman if autotune suggests literally no changes, that is an error. It should always adjust things slightly if it has good data.
Grant: the conversions of voltages into percentages is done in the edison-voltage script. If you'd like to try to figure out a better formula for doing so, that would be useful. I believe @cjo20 created the current one.
Scott Leibrand
@scottleibrand
May 16 2017 15:40
@mhaeberli COB gets decayed based on actual observed absorption via positive BG deviations. Were you missing CGM data? If you're on dev, raising min_5m_carbimpact is a good way to get COB to decay faster in the absence of deviations.
Chris Oattes
@cjo20
May 16 2017 15:48
I did. You won't find something that fits everyone, becuase it varies depending on the specific battery (even different batteries with the same capacity will vary). Dying while still at 40% seems odd though, that should be well above the point where it will cut off.
12-14 hours sounds more like a 1.5Ah battery. What sort of battery is it?
garykidd
@garykidd
May 16 2017 15:53
@scottleibrand yeah---two explorer rigs...will set up some more soon. I'm thinking its the fact that I don't actually have my chip bolted down---though it is shrink wrapped tightly.....but it's easy to ccprog again (now). Still, was wondering if others are having this issue--might it make sense to automate the ccprog re-write sequence within the loop. I may be recalling incorrectly or like Roger Clemens said..misremembering, but I believe you shred that others have commonly experienced these issues....thoughts?
Scott Leibrand
@scottleibrand
May 16 2017 16:00
it does happen occasionally to some people. I haven't had much problem with it, but mine are securely bolted down, so maybe that contributes. I would be reluctant to automate a re-flash unless/until we figure out what causes the problem
Lorenzo Sandini
@lsandini
May 16 2017 16:00
Another strange question, sorry about that. How can I SSH into my Edison, while it is tethered to my iPhone ? I know this is probably possible with reverse SSH tunneling, but I am not sure how to do that. I think Scott mentioned he uses it ?
Scott Leibrand
@scottleibrand
May 16 2017 16:03
ssh from your phone, something on the same tethering network, or from a remote server?
Lorenzo Sandini
@lsandini
May 16 2017 16:06
I use Termius on my iPhone, but it would be convenient to use a computer on a different network, go through the iPhone and int the Edison :)
into
garykidd
@garykidd
May 16 2017 16:12
@scottleibrand gotchya. I'v eonly noticed it when I've left from hom wifi connection to BT....but that also means that it's probably in my pocket with greater chance of jarring loose. it does seem really tight though....and wouldnt you think you might have aproblem reflashing if it had become loose (unless it's just intermittent I guess).
Eric
@ecc1
May 16 2017 16:18
@lsandini You'll be able to ssh from a ssh client on your phone (you just have to find the rig's IP address on the BT tethering network). Doing it from another host will be hard or impossible, I suspect. It would require the phone to do routing and NAT between its external (WiFi or cellular) network and the BT network. On Android, at least, this isn't enabled by default. I haven't tried very hard to set it up, so maybe it's possible.
So reverse SSH tunneling is probably the right approach
Scott Leibrand
@scottleibrand
May 16 2017 16:25
That or an openvpn client like @thebookins (I think?) was working on...
Lorenzo Sandini
@lsandini
May 16 2017 16:28
I figured it would be difficult, that's why I like the "reverse tunneling" approach. The SSH server on the edison would start the connection towards a computer in the outside world, for example my home computer (A). Then I could use my office computer (B) to contact my home computer and that connection would be made. OK let me have a look at openvpn, thanks for the hint.
Martin Haeberli
@mhaeberli
May 16 2017 16:35
@scottleibrand thx - yes, missing CGM data … we’re sort of transitioning as an initial step to trying to use it for overnight, eg low bg suspend, etc. to use it 7x24 we need a bit more CGM data discipline - Dexcom share is often a real PITA if the iPhone, Dexcom receiver, and transmitter on the patient wander away from each other too far, then it much too often has to be reset by hand
Scott Leibrand
@scottleibrand
May 16 2017 16:37
This is what I do instead of autossh:
if ! /bin/ps -ef | /bin/grep ssh | /bin/grep $1 | /bin/grep -v grep | /bin/grep -v launch; then
    /usr/bin/ssh -fN -R $1:localhost:22 you@yourserver.net
else
  #/usr/bin/killall -g --older-than 12h ssh
  if ! /bin/ps -ef | /bin/grep sshd | /bin/grep pts/ | /bin/grep -v grep; then
      /usr/bin/killall -g --older-than 10m ssh
  fi
  ping -c 10 diyps.net || /usr/bin/killall -g --older-than 10m ssh
fi
Lorenzo Sandini
@lsandini
May 16 2017 16:39
Uuuhh, sounds like eskimo language to me :(
is this something that could go into the docs, under "How to access your OpenAPS rig" ?
elodaille01
@elodaille01
May 16 2017 16:57
Hi there ! @scottleibrand please, could you troubleshoot me about the classic problem : VirtualBox only showing 32 bit guest versions on my 64 bit host OS ? (autotune set up, step 0)
thank you ;)
Scott Leibrand
@scottleibrand
May 16 2017 17:02
unfortunately I don't have any experience with the 32-bit thing myself, as I have only run autotune on OpenAPS rigs and on a Mac. you might ask in https://gitter.im/openaps/autotune
@lsandini no, most people don't have their own cloud servers, and for someone who doesn't know how to securely administer one, I wouldn't want them to open up a tunnel for some hacker to get in and take remote control of their self-built medical device
I think the openvpn option would be a better general purpose solution if anyone wants to figure out all the nuances of helping ordinary users set that up.
Matthew Williams
@mwilliams
May 16 2017 17:05
@scottleibrand Added some updates to the MDT SMB PR, looks like I'm smb looping (a few date errors in there, but it doesn't look like it's impacting the smb-suggested bits?). Regardless, I'm going to grab lunch shortly, so I'll see what the afternoon brings and if I get any SMB events in NS. I'll keep the PR updated (in fewer comments, sorry for being noisy!)
Scott Leibrand
@scottleibrand
May 16 2017 17:05
:+1:
I think there are some differences with the Enlite glucose.json format that violate some of the assumptions for those jq commands.
Matthew Williams
@mwilliams
May 16 2017 17:08
Yeah, sounds about right given the previous MDT work that needed to be done
brandonschmidt
@brandonschmidt
May 16 2017 17:26
@elodaille01, this might an issue with your BIOS settings. Generally speaking, VirtualBox requires the Intel Virtualization Technology and VT-d options to be enabled in BIOS, assuming you have an Intel processor. (Note I don't have a rig yet, but I do use VirtualBox at work.)
Lorenzo Sandini
@lsandini
May 16 2017 17:38
@scottleibrand ok it sure is a good reason not to.
fidoman
@efidoman
May 16 2017 18:08
@scottleibrand - I will re-run autotune and see if it doesn't change the values a bit this time. These are the basal profiles I loaded in my nightscout profile and in my pump after running autotune about 2 weeks ago.
tynbendad
@tynbendad
May 16 2017 18:08
@scottleibrand thx, will save that for next time!
apabari
@apabari
May 16 2017 18:50
Hello! Have been reading about SMB on Twitter and it sounds like those who have tested are seeing good results. Could anyone point me at any documentation that would explain how I can get involved with testing?
Matthew Williams
@mwilliams
May 16 2017 18:51
@apabari openaps/oref0#424 The PR has a good amount of info
apabari
@apabari
May 16 2017 18:57
Thank you! Reading through the info now.
gkreiner
@gkreiner
May 16 2017 18:59
How do "reset" my PuTTY editor? I messed up. (trying to get started setting up network). I want to get back to the system asking me for user name and pw.
I tried powering off. Exiting. Nothing gets me back to the starting point.
PieterGit
@PieterGit
May 16 2017 19:05
@scottleibrand : i think openaps/oref0#456 can be merged to dev
Dana Lewis
@danamlewis
May 16 2017 19:32
@gkreiner have you done the unplug replied dance?
Is edison well seated on the board?
apabari
@apabari
May 16 2017 19:41

Hi... I read through all the material, and believe I followed the instructions - and I am able to complete the set-up with the supermicrobolus flag enabled. But, before enabling any other settings in preferences.json, I am seeing this error message in the log:

Waiting up to 4 minutes for new BG: ls: cannot access monitor/pump_loop_completed: No such file or directory

Just seems to hang there and keeps repeating itself
Dana Lewis
@danamlewis
May 16 2017 19:42
It's going to wait til it gets a new bg
The other error will clear once it runs a loop
apabari
@apabari
May 16 2017 19:42
Ah, okay... I will wait then! Thanks :)
Jason Wittmer
@jbwittmer
May 16 2017 19:48
With respect to SMB, am I understanding the remainingCarbsCap correctly? If it is set to zero the SMB will be "less aggressive" than if it is set to a non-zero number approximating a large meal? A non-zero number allows the algorithm to deliver insulin earlier even if not seeing a rise in the CGM value? And the higher the value the more aggressive it will be?
Matthias
@ceben80
May 16 2017 19:48
@danamlewis regarding this bg waiting phase I assume it's less rig battery consumption?
apabari
@apabari
May 16 2017 19:50

@danamlewis How long should I wait for a loop to complete? I can see BG entries are being uploaded (on NS). This is an excerpt from my log.

``Starting supermicrobolus pump-loop at Tue May 16 15:46:41 EDT 2017 with 27 second wait_for_silence: Waiting up to 4 minutes for new BG: ls: cannot access monitor/pump_loop_completed: No such file or directory Radio ok. Listening: .No pump comms detected from other rigs Preflight OK. Profile less than 60m old. find:monitor/pump_loop_completed': No such file or directory
pump_loop_completed less than 5m ago. Refreshed pumphistory
pumphistory.json: "TempBasalDuration 2017-05-16T15:45:02 head[2], body[0] op[0x16]"
Checking pump clock: "2017-05-16T15:46:32-04:00" is within 1m of current time: Tue May 16 15:47:40 EDT 2017
Error, retrying
Waiting for 30s silence before mmtuning
Radio ok. Listening: .No pump comms detected from other rigs
Listening for 30s silence before mmtuning: .No pump comms detected from other rigs
mmtune: "916.660", 5, -62 waiting for 4 second silence before continuing
Radio ok. Listening: .No pump comms detected from other rigs
Sleeping 7;

Starting supermicrobolus pump-loop at Tue May 16 15:49:19 EDT 2017 with 5 second wait_for_silence:
Waiting up to 4 minutes for new BG: ls: cannot access monitor/pump_loop_completed: No such file or directory
Radio ok. Listening: .No pump comms detected from other rigs```

Scott Leibrand
@scottleibrand
May 16 2017 19:51
@jbwittmer correct
Jason Wittmer
@jbwittmer
May 16 2017 19:52
Thanks.
Scott Leibrand
@scottleibrand
May 16 2017 19:53
@ceben80 yes, and to help make sure it enacts temps/SMBs as quickly as possible after each new BG
Matthias
@ceben80
May 16 2017 19:56
Very good tuning :star2:
Jason Wittmer
@jbwittmer
May 16 2017 19:57
@apabari I'm not sure but it looks like you might be seeing the same issue I was last night when trying to get SMB running. Your pump clock and rig clock must be within 60 seconds of each others, and yours is 68 second apart? I think? I'm just getting started myself so sorry if I'm on the wrong track.
Scott Leibrand
@scottleibrand
May 16 2017 19:57
@apabari Checking pump clock: "2017-05-16T15:46:32-04:00" is within 1m of current time: Tue May 16 15:47:40 EDT 2017
Error, retrying
apabari
@apabari
May 16 2017 20:00
Oh, okay... sorry, it's been a while since I've been on here to make any changes! I assumed the clocks aligned themselves regularly. I need to re-align them?
Scott Leibrand
@scottleibrand
May 16 2017 20:06
Until we make that part of the loop you do. SMB is a lot luckier than oref1 was, as it uses the pump clock to determine if it's time to do another SMB yet.
gkreiner
@gkreiner
May 16 2017 20:11
@danamlewis Hi Dana. (Thanks) The Edison is totally secure. I unplugged, re-plugged all cables, rebooted my computer. Nothing has helped so far. Any ideas of how to get the unit talking and started with username and pw login?
apabari
@apabari
May 16 2017 20:12
@scottleibrand Ah, ok. Will this do? openaps use pump set_clock --to now
Martin Haeberli
@mhaeberli
May 16 2017 20:13
getting messages on my console :
[58332.889804] wl_android_wifi_off in
[58332.900774] wifi_platform_set_power = 0
[58340.614186] 
[58340.614186] Dongle Host Driver, version 1.141.59 (r)
[58340.614186] Compiled in /home/robin/src/edison-linux-helper/edison-bcm43340 on Apr  4 2017 at 22:42:52
[58340.614369] wl_android_wifi_on in
[58340.634469] wifi_platform_set_power = 1
[58341.184484
any suggestions on how to quiet them down?
Scott Leibrand
@scottleibrand
May 16 2017 20:15
Or oref0-set-device-clocks
apabari
@apabari
May 16 2017 20:21
@scottleibrand Thanks
gkreiner
@gkreiner
May 16 2017 20:21
@danamlewis You can disregard my last question. After unplugging the battery and re-plugging, this seemed to fix the problem. Thanks again!
Martin Haeberli
@mhaeberli
May 16 2017 20:39
@esialb robin - any thoughts on my question just above?
katie disimone
@Kdisimone
May 16 2017 20:40
@mhaeberli those are the kernel messages. I haven't found a way to get rid of them when I'm using screen mode either. They don't show when I'm on ssh though.
Martin Haeberli
@mhaeberli
May 16 2017 20:50
@Kdisimone thx - on one of my devices (native 0.1.1 kernel) it somehow doesn’t seem so chatty, I think; on my other (upgraded per Robin’s advice to 0.1.1 by expanding the kernel-only zip at root) - the chattiness continues
katie disimone
@Kdisimone
May 16 2017 20:51
@mhaeberli I think my newer jubilinux rigs are also chattier for sure. Older jubi rigs don't have that
Martin Haeberli
@mhaeberli
May 16 2017 20:51
:+1:
elodaille01
@elodaille01
May 16 2017 20:52
@brandonschmidt thank you very much, it confirms what I have read..thank you !!!
Martin Haeberli
@mhaeberli
May 16 2017 20:53
also, since the diurnal cycle is more active (that is, more people are likely more awake), has anyone else figured out why sometimes openaps may need to be “kicked” to get new blood sugar data from NightScout (when the data is already present), and other times not? and how to make sure it’s not needed? otherwise, I’ll be following @scottleibrand ’s recent advice and tearing down into the aliases and logs ...
Tim Street
@tim2000s
May 16 2017 21:03
@mhaeberli that's not an issue I've ever seen.
elodaille01
@elodaille01
May 16 2017 21:37
@brandonschmidt I haven't any 'advanced menu' in my BIOS ! (to go in 'CPU configuration')..what should I do, please ? (Packard Bell, Windows 10)..thank you !!
brandonschmidt
@brandonschmidt
May 16 2017 21:44
What's the make of the computer?
Model*
Do you see any options labeled "Virtualization" if you go through the various BIOS tabs?
Also, you may need to disable
the Hyper-V feature in Windows and reboot
kenkotch
@kenkotch
May 16 2017 21:56
when flashing my edison, i see the following ~10 times, each with different leading characters. Is this of concern?
[ 13.168278] pca953x 1-0022: failed reading register
Scott Leibrand
@scottleibrand
May 16 2017 22:03
Nope. It's trying to detect a different kind of base board you're not using (maybe the Arduino one)
rsilvers129
@rsilvers129
May 16 2017 23:16
If there were an ITTT hear-rate trigger for Apple Watch, then it could POST to NightScout your HR or HR zone. Then OpenAPS could see that.