These are chat archives for nightscout/intend-to-bolus

3rd
Jun 2017
jcorbett80
@jcorbett80
Jun 03 2017 00:38
For those using TI stick here is a 3d print case. He has a full and also a backless to stick to pi, phone, or what ever also. I am ordering the full. I will update if it is good. https://www.shapeways.com/product/PGQ26J9UG/ti-cc1111-rf-transceiver-protective-case?optionId=40496520&li=more-from-shop
Martin Haeberli
@mhaeberli
Jun 03 2017 01:16
is it just me or is the CGM BG maximum on G5 smaller than on G4?
G5 seems to max out at 300? Do I remember G4 capping out at 400?
Scott Leibrand
@scottleibrand
Jun 03 2017 01:18
the max BG reading on a G4 is 400. What are you seeing that makes you think the G5's maximum is 300?
Martin Haeberli
@mhaeberli
Jun 03 2017 01:19
real-time data on T1’s G5 share app phone vs BG finger prick - flat mesa top at 300 - but finger BG was 318 in the middle of the mesa
don’t know for sure though
we had fun yesterday - accidental double bolus etc reminded us minimum is 40
Scott Leibrand
@scottleibrand
Jun 03 2017 01:20
I'd take a look at the actual data in the NS API or similar and see if they were actually at 300 +0 for an extended period or if it was a more natural plateau
Martin Haeberli
@mhaeberli
Jun 03 2017 01:21
once the data gets there - we’re in the middle of losing a bit of a long technology war with use of Dexcom G5 which we have been trying to change over to for 3 days ...
support is great, 7x24 but other things - not so much
Aaron Michelson
@Aaybob
Jun 03 2017 02:11
@Sgoldberg89 nice! You are sure you were offline? You rebooted after commenting out your wifis? It was updating temp basals?
@Sgoldberg89 I'm trying swaping modules and cords around. The explorer board that had connection with another compute module.
Aaron Michelson
@Aaybob
Jun 03 2017 02:17
@Sgoldberg89 I got an old board to run that wasn't running "lsusb". It sees receiver 22a3:0047 just by plugging it in a few times. (I ran the command line lsusb 1 second after plug in...don't know if that helped)
l
@Sgoldberg89 And its looping offline!
Aaron Michelson
@Aaybob
Jun 03 2017 02:26
@mhaeberli there is an option to use 300 as max or 400 as max in the menus.
Martin Haeberli
@mhaeberli
Jun 03 2017 02:41
Interesting - in hindsight my graph turned out to go to 400
Cameron Chunn
@applehat
Jun 03 2017 02:58
I can confirm that a g5 goes to at least 380 because I saw it happen before my loop :p
rsilvers129
@rsilvers129
Jun 03 2017 02:59
I unplugged my charging cable and the rig turned off. The cable was in the rightmost port. Either port charges it, right?
Also today I was sleeping and woke up and the rig had been off for 25 minutes. I looked at the pump and it was doing a 30 minute temp basal of 3.75, which I needed to keep my BG in a good range due to the meal I had eaten earlier. I was thinking it was a nice benefit that even though the rig had an outage, the pump was still making use of its last command.
Dana Lewis
@danamlewis
Jun 03 2017 03:06
Yes, either port charges.
rsilvers129
@rsilvers129
Jun 03 2017 03:20
I wonder why all LEDs went off the instant I unplugged the cord. Then when it booted, it had the py ratio error in the log. So I unplugged the battery, put it back, started it up, and it was fine.
Martin Haeberli
@mhaeberli
Jun 03 2017 03:34
@applehat :+1:
Cameron Chunn
@applehat
Jun 03 2017 04:43
How hot can these Edison's get before they self district? I know there is probably some thermal throttling built in....but I just checked mine and it was at 90°C
Destruct*
Cameron Chunn
@applehat
Jun 03 2017 04:56
It's frustratingly hard to find anything about an Edison.
I guess the Atom on the board will underclock at 100c and shut down at around 120c.... Tho I can't help but think that it's not all that safe to crank out those temps next to a lipo. In my pocket.
Aaron Michelson
@Aaybob
Jun 03 2017 05:13
Continue? y/[N] y
Checking /root/myopenaps: Traceback (most recent call last):
File "/usr/local/bin/openaps", line 6, in <module>
exec(compile(open(file).read(), file, 'exec'))
IOError: [Errno 2] No such file or directory: '/root/src/openaps/bin/openaps'
Can't init /root/myopenaps
This happens when installing per documentation. Has a bug crept in?
@applehat they do get hot. I'd not put the processor side against the battery. My rigs get hot, I think some more than others but not an instant burn heat...
Ryan Dalisky
@rdalisky
Jun 03 2017 05:39
Has anyone made an ifttt button for carb entry to NS? I'm trying to figure out the body portion, how each press would add 5mg carbs to my COB. Anyone have a recommendation?
Cameron Chunn
@applehat
Jun 03 2017 05:46
Look at the docs for "low correction" with ifttt
I just stuck a little heatsink off a pi2's processor on my rig. I do notice it seems to get hotter when charging (as is expected)
I'll let it sit and see if it gets as hot with this joke of a heat sink.
Matthias
@ceben80
Jun 03 2017 05:49
@applehat impressive
Benjamin Mammon
@bmammon
Jun 03 2017 05:50
i'm stuck! I just set up my new edison/explorer board and tried running the script
Starting pump-loop at Fri Jun 2 22:45:41 PDT 2017:
Traceback (most recent call last):
  File "/usr/local/bin/mmeowlink-any-pump-comms.py", line 15, in <module>
    app.run(None)
  File "/usr/local/lib/python2.7/dist-packages/decocare/helpers/cli.py", line 113, in run
    self.prelude(args)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/cli/any_pump_comms_app.py", line 28, in prelude
    super(AnyPumpCommsApp, self).prelude(args)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/cli/base_mmeowlink_app.py", line 26, in prelude
    self.link = link = LinkBuilder().build(args.radio_type, port)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/link_builder.py", line 16, in build
    return SubgRfspyLink(port)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 55, in __init__
    self.open()
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_interface.py", line 27, in open
    self.serial = spi_serial.SpiSerial()
  File "/usr/local/lib/python2.7/dist-packages/spi_serial/spi_serial.py", line 7, in __init__
    self.cs0 = m.Gpio(23)
  File "/usr/local/lib/python2.7/dist-packages/mraa.py", line 649, in __init__
    this = _mraa.new_Gpio(*args)
ValueError: Invalid GPIO pin specified
mmtune: monitor/mmtune.json  raised  Invalid GPIO pin specified
pump://JSON/mmtune/monitor/mmtune.json
Traceback (most recent call last):
  File "/usr/local/bin/openaps-report", line 82, in <module>
    app( )
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/__init__.py", line 51, in __call__
    self.run(self.args)
  File "/usr/local/bin/openaps-report", line 75, in run
    output = app(args, self)
  File "/usr/local/lib/python2.7/dist-packages/openaps/cli/subcommand.py", line 52, in __call__
    return self.method.main(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/reports/invoke.py", line 40, in main
    output = task.method(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/uses/use.py", line 44, in __call__
    self.before_main(args, app)
  File "/usr/local/lib/python2.7/dist-packages/openaps/vendors/medtronic.py", line 62, in before_main
    self.setup_medtronic( )
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/mmeowlink.py", line 92, in setup_medtronic
    setup_medtronic_link(self)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/mmeowlink.py", line 75, in setup_medtronic_link
    link = builder.build(radio_type, port)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/link_builder.py", line 16, in build
    return SubgRfspyLink(port)
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/subg_rfspy_link.py", line 55, in __init__
    self.open()
  File "/usr/local/lib/python2.7/dist-packages/mmeowlink/vendors/serial_interface.py", line 27, in open
    self.serial = spi_serial.SpiSerial()
  File "/usr/local/lib/python2.7/dist-packages/spi_serial/spi_serial.py", line 7, in __init__
    self.cs0 = m.Gpio(23)
  File "/usr/local/lib/python2.7/dist-packages/mraa.py", line 649, in __init__
    this = _mraa.new_Gpio(*args)
ValueError: Invalid GPIO pin specified
Usage: grep [OPTION]... PATTERN [FILE]...
Try 'grep --help' for more information.
 Listening: ....................................................................................................Error, retrying
I keep getting this message. Any ideas?
Cameron Chunn
@applehat
Jun 03 2017 05:52
Explorer board?
Benjamin Mammon
@bmammon
Jun 03 2017 05:53
yes?
Cameron Chunn
@applehat
Jun 03 2017 05:53
Did you accedently tell oref0 you were not using an explorer explorer​?
It looks like it's trying to talk over a Pi's GPIO ports to a radio module instead of using the onboard explorer radio.
Benjamin Mammon
@bmammon
Jun 03 2017 05:55
i used the automatic setup and pretty sure i said yes to explorer board
Are you using an Explorer Board? y/[N] y
Ok, yay for Explorer Board!
Cameron Chunn
@applehat
Jun 03 2017 05:56
Try running it again :shrugs:
Someone else might know better.
@ceben80 it's hovering around 75°C right now with the heat sink and no fam
Fan*
Running autotune to give it some load.
It hit 90°C before this sync.
Sink. Sorry. I just can't type tonight.
I need to check Alibaba and see if I could get a run of specific to the Edison heat sinks made.
Benjamin Mammon
@bmammon
Jun 03 2017 06:01
hey, do you remember how to kill all?
i want to start again but make sure nothing is running
Cameron Chunn
@applehat
Jun 03 2017 06:08
Killall openaps would do it.
Or just delete everything in cron and reboot it.
Matthias
@ceben80
Jun 03 2017 06:15
@applehat my edison is running not so overheated, luckily, so that I'm using a box with less height, 20mm (posted pic yesterday in twitter), built in an external Adafruid charger......
Ryan Dalisky
@rdalisky
Jun 03 2017 06:32
Thanks everyone, that makes sense.
Cameron Chunn
@applehat
Jun 03 2017 07:25
@ceben80 I think the internal charger has a lot to do with it, honestly.
I'm going to do a bit if testing. An external charger could have some real benefits in a case like you posted on Twitter as well... It could power on a tiny case fan to cool during charge as well.
Cameron Chunn
@applehat
Jun 03 2017 07:30
I'm going to let mine come to rest and then see what kind of heat gains I get on a charger.
Matthias
@ceben80
Jun 03 2017 08:43
@scottleibrand short Q, as you know @lukas-ondriga has been implemented offline temptarget.json via https://github.com/lukas-ondriga/openaps-share#android
Now I want implement as well using http-request App for carb entries . Many of you are using IFTTT but I won't rely on the internet.
Any advice for me (like the temptarget stuff), but I don't know how-to....
Thanks in advance :wink:
Diadon81
@Diadon81
Jun 03 2017 08:47
So as a result of my meeting with endocrinologists in Endocrinic Science Center (Russia), one of them with diabetes dicide to try a rig. I give him my backup rig with stable version of oref0.
Tim Street
@tim2000s
Jun 03 2017 09:54
@ceben80 - the HTTP server we are using for serving web pages doesn't support enough to use for treatment entries. I think you'll need to add an additional one. In addition, you need to modify how the rig handles carb history from night scout to stop it over writing anything created locally with a blank file when it can't find anything.
@applehat when you get to 90C they normally shutdown. That's supposed to be the max operating temperature.
Matthias
@ceben80
Jun 03 2017 10:09
@tim2000s thanks, my aim is to get rid of the internet dependency to use all openaps features offline especially the SMB stuff, IFTTT is a nice feature but not usable without internet
Tim Street
@tim2000s
Jun 03 2017 10:14
There's been some discussion about it. I think I know how to do it, including a graphical display of future BG, but need to work out the building blocks, which takes a bit of time.
@danamlewis mentioned there's someone working on it as well.
fidoman
@efidoman
Jun 03 2017 10:16
@applehat - 90 degrees C is the threshold according to the unix sensors program. I do think it very risky to to keep it in your pocket when the CPU core is 90 degrees. I had a friend print me one of those cases with separation from the battery and venting and I monitor the temperature in a log on the rig. I've checked the log a few times when it was in my pocket and it never goes over 67 degrees C. A few weeks back I was trying out a prototype of this case and the battery compartment was too tight. In my stupidity, I used a screw driver to pull it out and shorted out the battery. It basically exploded and it was like holding a firecracker in my hand. Fire and smoke everywhere. I just through the entire rig on the ground. Luckily, due to the separation, the rig somehow escaped without damage and is still working fine to this day. I'll try to post a picture of the melted prototype case. :+1:
Matthias
@ceben80
Jun 03 2017 10:18
@tim2000s Sounds good :+1:
fidoman
@efidoman
Jun 03 2017 10:19
Screenshot from 2017-06-03 06-19-03.png
Matthias
@ceben80
Jun 03 2017 10:23
Uuui....
fidoman
@efidoman
Jun 03 2017 10:25
my new case is a fraction bigger to allow more room for the battery and even has room for a spare AAA pump batter in the lid. You can see it in the pic below.
IMG_5010.JPG
Jesse Szypulski
@Kryptonit3
Jun 03 2017 16:23
I don't know if there is a setting or not or I set something wrong, but for the past few days or so I would notice my blood sugar get down to the 60's and then I would look at pump and see a temp basal of 1.3U/hr (my default). Personally, if my blood sugar drops below 85-90 I would like a basal of 0U/hr til it comes back up.
Jun 03 08:25:32 krypto_diabetus pump-loop.log:  {"temp":"absolute","bg":69,"tick":-9,"eventualBG":58,"snoozeBG":58,"predBGs":{"IOB":[69,61,54,48,42,39,39,39,39,39,39,39,39,39,39,39,39,39,40,41,42,43,44,45,46,46,47,48,48,49,49,49,50,50,50,50,51,51,51,51,51,52]},"IOB":-1.092,"reason":"COB: undefined, Dev: -55, BGI: 2.58, ISF: 40, Target: 110; BG 69<75","duration":30,"rate":0}
Jun 03 08:25:41 krypto_diabetus ns-loop.log:  Uploaded
Jun 03 08:25:43 krypto_diabetus pump-loop.log:  pump://JSON/set_temp_basal/enact/enacted.json
Jun 03 08:25:44 krypto_diabetus pump-loop.log:  reporting enact/enacted.json
Jun 03 08:25:44 krypto_diabetus pump-loop.log:  {"requested":{"duration":30,"rate":0,"temp":"absolute"},"bg":69,"temp":"absolute","snoozeBG":58,"timestamp":"2017-06-03T08:25:42.606193","predBGs":{"IOB":[69,61,54,48,42,39,39,39,39,39,39,39,39,39,39,39,39,39,40,41,42,43,44,45,46,46,47,48,48,49,49,49,50,50,50,50,51,51,51,51,51,52]},"rate":1.3,"reason":"COB: undefined, Dev: -55, BGI: 2.58, ISF: 40, Target: 110; BG 69<75","eventualBG":58,"recieved":false,"duration":27,"tick":-9,"IOB":-1.092}
In one of those it says the blood sugar is 69 and has a rate of 1.3. I haven't had any carbs for over 12 hours and have not given any insulin for the same time.
dougtakeuti
@dougtakeuti
Jun 03 2017 17:05
I’ve been testing SMB for a few days and the results seem great. However, the rig has frequently stopped uploading BG data to NS. It uploads treatments as can be seen in the image and the latest bg shows in the Openaps pill and in pump-loop.log. glucose.json is current and correct. ns-loop.log seems to be fine. The graph will be blank for one or two hours and eventually come back again. Any ideas where I could look for the problem?
image.png
Martin Haeberli
@mhaeberli
Jun 03 2017 17:17
@dougtakeuti : a) what CGM are you using; b) how is it configured to get the data to the rig ?
or from the rig to nightscout
what is happening for you looks similar to what we have going on recently, but we have a G5 -> which goes to Dexcom share -> which is pulled to Nightscout -> which is pulled by our rig. Nightscout is configured to get the last 72 samples or so (6 hours), and G5 does “gap-filling” in my language, where when the data comes online again (G5 wearer comes near iPhone) the last few hours of data are brought in, albeit late.
John Benjamin
@Bender1061
Jun 03 2017 17:19
@dougtakeuti If you are using MDT, use the latest dev, I made a change to when the nightscout/glucose.json is made and that fixed the inconstant CGM upload.
dougtakeuti
@dougtakeuti
Jun 03 2017 17:22
@Bender1061 Yes, I'm using MDT. When did you made the change? I updated the rig last week.
John Benjamin
@Bender1061
Jun 03 2017 17:30
friday
dougtakeuti
@dougtakeuti
Jun 03 2017 17:30
ok, I'm doing it then. thanks!
John Benjamin
@Bender1061
Jun 03 2017 17:32
:+1:
dougtakeuti
@dougtakeuti
Jun 03 2017 17:36
I just got my 2nd pump reset when calibrating the cgm. Pretty annoying. Are there any other occasions when that would happen? I thought is was only when using the bolus wizard.
John Benjamin
@Bender1061
Jun 03 2017 17:39
I've only had it once, and I was not sure what was happening at the time but SMB was enabled, so I
'
I'm thinking it was that
Tim Street
@tim2000s
Jun 03 2017 17:42
I think it's any button presses whilst a bolus instruction is being delivered.
dougtakeuti
@dougtakeuti
Jun 03 2017 17:44
I see... not safe for a child on her own then. Pity...
rsilvers129
@rsilvers129
Jun 03 2017 17:58
Happened to me again. I was 15-20 minutes from McDonalds and about 132 BG, took a large bolus, drove there. No traffic this time. It seemed perfect as my levels just pivoted and I could see them just starting to come down. But… the world’s longest wait at McDonalds. About 15 minutes later I had my food. I went down to LOW. I take it back. The longest wait I had at McDonalds was in Russia in 1991. Three hour wait if I didn’t pay someone to skip the line.
@mhaeberli @dougtakeuti The gap filling of G5 bridge is a Heroku variable BRIDGE_MAX_COUNT. Setting it to 10 would do 50 minutes of gap filling.
Cameron Chunn
@applehat
Jun 03 2017 18:49
Question about max_iob. The "rule of thumb" is to not set it more then 3x your highest basal rate. Does this mean if the highest rate I had set before looping was 2u/hr, that it should be 6?
Also, what should I set my pumps "max basel" setting too?
I never used temp basals before looping, so that setting was never adjusted pre-op
rsilvers129
@rsilvers129
Jun 03 2017 19:18
Set the max basal rate to whatever will allow your other settings to work.
@scottleibrand @danamlewis if I manually set a temp basal so I can do an activity, will the rig see it and honor it for the duration that I set? I am not sure that simply setting a higher target is my answer for running and biking. I tried it today and still had to have 20 grams of carb over an hour to not go low. However I have found that setting a temp rate about 15 percent of my normal rate works well.
Scott Leibrand
@scottleibrand
Jun 03 2017 19:43
It will reset any temp you set unless you suspend. Better to set a high target high enough to achieve the negative IOB you want. You can go as high as 200 or maybe a bit higher.
Katie Aldridge
@kcrcgm
Jun 03 2017 20:02
Hello, first time here! I'm having trouble with the driver for the edison. I have (twice) installed the driver successfully onto my computer, but I can't get my computer to recognize it. I keep getting this when I try to choose a driver for the edison: "Windows could not find driver software for your device". I have tried manually searching and selecting the driver and also tried letting the computer automatically search for the driver. Can someone help? TIA!
jtsackdex
@jtsackdex
Jun 03 2017 20:15
I have My rig working Wi-Fi is very stable. Bluetooth tethering is questionable. Which oref0 do I need to run to do Camping? Dev or master?
fidoman
@efidoman
Jun 03 2017 20:41
I switched back last night to just using meal assist without SMB. It may be an anomaly again, but today my blood sugar doesn't spike after meals like it does whenever I'm using SMB. It's just a gut feel but I look at my charts while using SMB and it seems that most of the time it is zero temping. Sometimes it does it for what seems like 2 hours before and 2 or more hours after a meal. That has to be contributing to the high peaks after meals when SMB is enabled. I'll be glad to test SMB again if an advanced parameter becomes available to allow me to dial back the SMB zero-temping post meals. For now, meal assist is doing a great job on its own at least in my case.
PieterGit
@PieterGit
Jun 03 2017 21:35
@esialb : I installed a new rig today with jubilinux 0.1.1. The ns-loop failed, because the edison voltage failed:
# cat monitor/edison-battery.json
root@edison:~/myopenaps# openaps upload-ns-status
Could not parse input data:  [SyntaxError: /root/myopenaps/monitor/edison-battery.json: Unexpected end of input]
root@edison:~/src/EdisonVoltage# ./voltage json batteryVoltage battery
Segmentation fault
I could fix it by unzipping kernel-v0.1.1.zip in /. Is that the suggested fix?
The monitor/edison-battery.json was empty (because of the segfault)
rsilvers129
@rsilvers129
Jun 03 2017 21:47
@ericfeibelman I am using AMA now also. But I have a suggestion that may help. Turn your DIA down. I was at 4 and found I would spike after a few hours. Today I tried 3. I ate 150 grams of carb!! Two filet o fish and two Blueberry & Cream pies. Master did an awesome job and kept me at 100 for three hours. After that, I did rise to 182, but still, awesome for such a supposedly off limits type of meal. I am testing a DIA of 2 and seeing what happens with that. I have some hope it may crush the tail rise, but it also make stack insulin and make me low, so I will monitor it and have Gatorade handy.
One thing I love about AMA is that when the rig dies from a low battery, or dies from a communication error (both happen to me too often) the 30 minute temp basals keep it all working until I can get it back online. With a series of boluses that suddenly stop being issued, I would risk rapidly elevating glucose. Today my pump battery died, and stopped receiving commands. But it had 27 minutes left on the temp basal, and I was able to replace the battery before that temp ended. I love it. It is a genius design.
rsilvers129
@rsilvers129
Jun 03 2017 21:56
Screen Shot 2017-06-03 at 5.52.36 PM.png
That pic is 150 grams carb.
PieterGit
@PieterGit
Jun 03 2017 22:03
I'm looking for volunteers that want to secure their nightscout and use token based authenction, see https://github.com/openaps/oref0/pull/470#issuecomment-305760550 for how to install, and see https://github.com/PieterGit/docs/blob/tokenbased/docs/docs/walkthrough/phase-1/nightscout-setup.md#switching-from-api_secret-to-token-based-authentication-for-your-rig for the suggestions to the docs.
garykidd
@garykidd
Jun 03 2017 22:13
@scottleibrand was thinking that it might be useful to create a way to check to see if BG data may be missing (and later available) for nightscout...without the need to backfill continuously when prior BG's are not needed...thereby reducing data burden. THoughts?
dougtakeuti
@dougtakeuti
Jun 03 2017 22:17
@Bender1061 Thanks for the fix! It seems to work well for us.
Scott Leibrand
@scottleibrand
Jun 03 2017 22:17
@garykidd what are you optimizing for?
PieterGit
@PieterGit
Jun 03 2017 22:18
@garykidd : i'm thinking of creating some kind of buffered-curl for uploads, so that if the rig can't upload it will upload again if there is network connection is back again.
Scott Leibrand
@scottleibrand
Jun 03 2017 22:19
@ericfeibelman there is a new smb-bolus-snooze branch you could test.
MelissaParkey
@MelissaParkey
Jun 03 2017 22:33
I am voluntarily throwing myself under the proverbial bus...
Is it possible to have messed up (software/firmware/code wise) an Edison such that the brilliant people can't fix it? 😳
garykidd
@garykidd
Jun 03 2017 22:34
@PieterGit that sounds cool. I guess that wouldn't cover scenario though where you've maintained network connectivity all along but just had gaps in BG data. But I see the usefulness in what your idea.
PieterGit
@PieterGit
Jun 03 2017 22:35
i use a dex connected to the rig by usb, so if the rig doesn't have cgm data, the receiver doesn't either.
i use https://github.com/ecc1/backfill to backfill my cgm data in nightscout from time to time
garykidd
@garykidd
Jun 03 2017 22:38
thinking it would be easy enough to detect CGM gaps and then utilize the above.....rather than network gaps.....for me...I never connect CGM receiver to usb....
PieterGit
@PieterGit
Jun 03 2017 22:39
in europe there is no other option, because the receiver doesn't support bluetooth
(that's for Dex G4)
rsilvers129
@rsilvers129
Jun 03 2017 23:52
@MelissaParkey No, I don’t think you can make a mistake that can’t be fixed. You can always start over and reflash the Edison. You can even reflash the Explorer radio if needed.