These are chat archives for nightscout/intend-to-bolus

7th
Jun 2017
Dana Lewis
@danamlewis
Jun 07 2017 00:01
it sounds like a lot of them are case-related. in interim, I’d take it out of the case or try a different case
David
@davidkeddydb
Jun 07 2017 00:02
@scottleibrand so just for fun I did a little experiment today. I just bolused and didn't enter any carbs. I have UAM and SMB enabled. I didn't go lower than 70 and I didn't go higher than 136. It does make me think I need to look at the COB Predbg as it least yesterday I was getting good results but not this good. Fantastic.
rsilvers129
@rsilvers129
Jun 07 2017 00:10
@davidkeddydb What did you eat?
My cases have the Edison exposed completely. But the charge controller is on the other side of the board. Even in the open air, it will burn you if you touch it. It foils my plans to sometimes walk around with the rig in my pocket and charging from an external USB pack.
Now I get pushovers when it reaches the temp threshold, so I will know.
David
@davidkeddydb
Jun 07 2017 00:37
@rsilvers129 I had yogurt and a waffle this morning. I had a granola bar and Chef Salad at one point and I am about to have a sub and bag of chips. This will be the biggest carb meal of the day. Guessing around 95 carbs or so. Just going to bolus again and go for the trifecta
Lin
@denglfddd
Jun 07 2017 01:05
屏幕快照 2017-06-07 09.04.36.png
Space is full
rsilvers129
@rsilvers129
Jun 07 2017 01:08
I am redesigning my case to be heavily ventilated now. It will be printed in 90 minutes. Then I can do a temp test with and without the vented version.
Annette Valle
@annettemvalle
Jun 07 2017 01:22
Is anyone on right now that could help me out? I just started openaps yesterday but have had a pretty rocky start. About 4 times now I have been able to get temp basals enabled but after 1 or 2 temp basals they stop. This is what the log looks like. @diabetic_dude_twitter told me this message was common but should resolve after 5 minutes. Mine doesn't seem to do this. Any suggestions? @JELCRAWFORD
@JELCRAWFORD thanks for the info on the data usage.
Ok, not sure how to upload a picture on here...
new6.PNG
Annette Valle
@annettemvalle
Jun 07 2017 01:28
I'm concerned about the part that says "BG data too old"
Scott Leibrand
@scottleibrand
Jun 07 2017 01:37
@annettemvalle how does your rig get BG data from your CGM?
Annette Valle
@annettemvalle
Jun 07 2017 01:37
@scottleibrand G5 share with Nightscout
Bob Duerr
@Duer0049
Jun 07 2017 01:38
Hey All, quick question, if I want to update my wife's rig to the Oref1 build, do I have to start from the beginning or just update the Oref0 currently on the rig?
Scott Leibrand
@scottleibrand
Jun 07 2017 01:39
@denglfddd try cd /; du -xh -d 3 | egrep "[1-9][0-9][0-9]M|[0-9]G" to see what is using up all your space in /
Dana Lewis
@danamlewis
Jun 07 2017 01:47
Lin
@denglfddd
Jun 07 2017 01:59
@scottleibrand root@edisonhost:~# cd /; du -xh -d 3 | egrep "[1-9][0-9][0-9]M|[0-9]G"
984M ./var/log
185M ./var/cache/apt
189M ./var/cache
1.3G ./var
1.4G .
Andy Sharrow
@dramageek
Jun 07 2017 02:35
It seems like I've seen a rise in overheating issues recently. I realize the desire to avoid pointing out potential problems with cases to avoid discouraging those contributing to the greater cause, but if there's a case or two causing overheating it's for the group's benefit to avoid problems. Are there designs that have problems?
Only asking because I've recently ordered two models printed, and would like to avoid any problems that could be coming. :smile:
Dana Lewis
@danamlewis
Jun 07 2017 02:47
I'm using soft cases and have never had an overheating issue, so can't say from my own experience. I also can't pinpoint specifics based on observing random comments yet, but does seem like the greater the amount of material covering the rig/thickness seems to correlate with those having overheating issues. I know people want durability/ protection, so not sure what the perfect balance might be between that and air flow/temperature
Scott Leibrand
@scottleibrand
Jun 07 2017 02:50
@denglfddd so it looks like /var/log is your culprit. You may need to go look at which log files are growing too big and see what is in them using up all the space. If you're not using the latest jubilinix, upgrading (reflashing) that might help...
Katie Aldridge
@kcrcgm
Jun 07 2017 03:03
I'm at this spot in the docs---Phase 2: ore0-setup.sh/ Step 0: Dependencies. I am having trouble installing the dependencies. I have a screenshot saved, but how do I upload a pic here? I read on down the page in the docs and saw that I can install the dependencies manually, but to do that, do I just copy and paste those 3 lines about packages? And is there something wrong with my setup so far that the automatic installation of dependencies isn't working? Thanks. I'm very inexperienced with all this.
Aaron Michelson
@Aaybob
Jun 07 2017 03:11
@scottleibrand April 4, 2017 jubilinux, latest version would run OpenAPS better than a jubilinux from December 2016. Could that make a stability difference?
Scott Leibrand
@scottleibrand
Jun 07 2017 03:13
Dunno. We are still using the original jubilinix and it's working fine. But some of the intervening versions had excessive kernel logging that filled up log files.
Aaron Michelson
@Aaybob
Jun 07 2017 03:14
@kcrcgm those three lines have to run correctly. If they report errors you need to re-flash. I tried to delete the packages that the command dpkg references because I was getting a message that it couldn't purge because of existing dependancies. But when I deleted them then I couldn't run the dpkg commands because package couldn't be found.
Lin
@denglfddd
Jun 07 2017 03:15
@scottleibrand So now i need to upgrade jubilinix, then re-install openaps?
Aaron Michelson
@Aaybob
Jun 07 2017 03:17
@scottleibrand would it help if somebody would add the "size" line to the logrotate file?
Katie Aldridge
@kcrcgm
Jun 07 2017 03:18
@Aaybob I got an Edison that was already flashed and am terrified of having to do that. So... if I install those three lines and it doesn't go well, then it's all messed up and I have to start from scratch? I'm thinking I shouldn't try it. Do you have any idea why I'm not able to do the auto install for dependencies?
Aaron Michelson
@Aaybob
Jun 07 2017 03:19
@kcrcgm are you on windows?
Katie Aldridge
@kcrcgm
Jun 07 2017 03:20
@Aaybob Yes
Aaron Michelson
@Aaybob
Jun 07 2017 03:20
Katie Aldridge
@kcrcgm
Jun 07 2017 03:23
@Aaybob I did all that page already. Added my name to the loops in progress. Read up about the offline looping and monitoring (but thought I had better wait to do that stuff), and I installed the shortcuts. Now I'm here http://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-2/oref0-setup.html#step-0-dependencies
Aaron Michelson
@Aaybob
Jun 07 2017 03:26
@kcrcgm Katie, you are? Okay I was talking about my page. For that line I would go to the page https://raw.githubusercontent.com/openaps/docs/master/scripts/quick-packages.sh to see what that does.
Annette Valle
@annettemvalle
Jun 07 2017 03:26
@kcrcgm I had the same problem and it was because the board OS is not compatible with the command that the instructions are giving us. you will have to install the sudo package so the board understands the bash command for the all in one script
David
@davidkeddydb
Jun 07 2017 03:27
@kcrcgm apt-get install sudo. Let that run and then do set up
Katie Aldridge
@kcrcgm
Jun 07 2017 03:27
@annettemvalle Is the sudo package later in the docs?
Aaron Michelson
@Aaybob
Jun 07 2017 03:27
@kcrcgm @annettemvalle that's the third line on my page...
@kcrcgm maybe you should start back there
Katie Aldridge
@kcrcgm
Jun 07 2017 03:28
@davidkeddydb Ok, so I type "apt-get install sudo"?
David
@davidkeddydb
Jun 07 2017 03:29
@kcrcgm yup
Aaron Michelson
@Aaybob
Jun 07 2017 03:29
@kcrcgm did you run the line from my page? apt-get install -y sudo strace tcpdump screen acpid vim python-pip locate
rsilvers129
@rsilvers129
Jun 07 2017 03:30
18920511_10156204001493662_6981097521517455910_n.jpg
Katie Aldridge
@kcrcgm
Jun 07 2017 03:31
@Aaybob I didn't. Do you think that would work better?
Aaron Michelson
@Aaybob
Jun 07 2017 03:31
@rsilvers129 are these 3D printers not outrageously expensive?
Annette Valle
@annettemvalle
Jun 07 2017 03:31
@rsilvers129 Looking good, it seems that mine needs a swamp cooler attached to the case to keep it cool
David
@davidkeddydb
Jun 07 2017 03:33
@kcrcgm did you already set up all your network stuff?
Aaron Michelson
@Aaybob
Jun 07 2017 03:34
@kcrcgm let me quote the lead writer, "Please make sure to complete ALL steps on this page. If you skip parts of step 0 and step 1, you will run into issues on step 2. " from the page: http://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-2/oref0-setup.html
Katie Aldridge
@kcrcgm
Jun 07 2017 03:34
@davidkeddydb Yes I did
David
@davidkeddydb
Jun 07 2017 03:35
👍
Katie Aldridge
@kcrcgm
Jun 07 2017 03:35
@Aaybob I know, that's why I haven't gone on. I'm a good student and want to do everything just as I'm told in the docs! ;)
David
@davidkeddydb
Jun 07 2017 03:36
Just get sudo and you'll be good to go. It is easy to miss
Aaron Michelson
@Aaybob
Jun 07 2017 03:36
It can't hurt to re-run and be careful that it runs without error. You have to be good. Otherwise the big D would have killed you.
Katie Aldridge
@kcrcgm
Jun 07 2017 03:37
Thanks everybody. I'll give it another go!
Aaron Michelson
@Aaybob
Jun 07 2017 03:37
It's actually really fast compared to trying to find why something isn't working
@kcrcgm you just do the six lines of code at 1.7 Install packages, ssh keys, and other settings and then you're back to setup.
Katie Aldridge
@kcrcgm
Jun 07 2017 03:45
@Aaybob Dumb question: Do I do one line at a time?
Aaron Michelson
@Aaybob
Jun 07 2017 03:46
offline loop works so great at home but never works at work.
yes one line at a time @kcrcgm that's not a dumb question its a legitimate question and one most people have.
Katie Aldridge
@kcrcgm
Jun 07 2017 03:47
That's my problem I think! I just copied the whole block and pasted it
Thanks!
Aaron Michelson
@Aaybob
Jun 07 2017 03:48
@kcrcgm I'm going to change that document to make it more clear now.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:48
often it's fine to paste the whole block, but sometimes that doesn't work. we've attempted to split up blocks that can't be pasted together, but if we've missed one, please do
Katie Aldridge
@kcrcgm
Jun 07 2017 03:49
Will it hurt anything to rerun those, since I'm not sure what I've done?
Cameron Chunn
@applehat
Jun 07 2017 03:51
What voltage does the pump radio shut down at? I haven't picked up lithium cells yet so I'm killing cheap cells fast and wanna stretch them till close to cut off.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:51
something like 1.21 V or so
but some pumps get flaky before that
@kcrcgm it won't hurt to re-run anything and everything, as long as you do it in order
Cameron Chunn
@applehat
Jun 07 2017 03:52
Word. So at 1.28v I'm probably good till tomorrow morning.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:52
a few of the steps where you're editing files it'll be obvious that it's already been done and you can't make the same edit twice, but if you're just running a command it should be fine
@applehat no idea how long it'll last. don't count on it being linear.
Katie Aldridge
@kcrcgm
Jun 07 2017 03:53
@scottleibrand Ok thanks!
Cameron Chunn
@applehat
Jun 07 2017 03:53
@scottleibrand oh right. I forgot that cells sag closer to their end.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:54
lithiums are worse, but pretty sure alkalines do it too
Cameron Chunn
@applehat
Jun 07 2017 03:54
I need to build a step down so I can just power it off 18650s.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:55
are there any rechargeable AAAs with enough voltage to work in the pump?
Cameron Chunn
@applehat
Jun 07 2017 03:56
Probably, but when how do I look like a crazy person with wires hanging out of my pump?
But then*
Scott Leibrand
@scottleibrand
Jun 07 2017 03:56
the things some people optimize for... ;-)
Cameron Chunn
@applehat
Jun 07 2017 03:58
Haha. So, there is a AAA that's a standard Li-ion cell that actually has a tiny regulator on it.
Scott Leibrand
@scottleibrand
Jun 07 2017 03:59
Interesting. I wonder how many mAh that can do above 1.25V, vs. an alkaline or lithium disposable
Cameron Chunn
@applehat
Jun 07 2017 04:03
Well they are rated at 2.8Wh. and most alkalines are something like 1.4Wh.
Aaron Michelson
@Aaybob
Jun 07 2017 04:04
What is a solution other than a re-flash if rerunning dpkg command of "install packages, ssh keys and other (1.7 of windows-edison)" has the error "did not purge because dependencies exist"?
Cameron Chunn
@applehat
Jun 07 2017 04:04
And since it's a 3.2-4.2v Li-ion, I imagine the regulator kicks out 1.5v till the battery is at 3.2v
Potential downside to a 3.7 cell regulated to 1.5 would be a complete lack of battery alarm - tho not necessarily a big deal if you can remember
Scott Leibrand
@scottleibrand
Jun 07 2017 04:11
@Aaybob usually apt-get install -f is suggested for errors like that
@applehat ah, yeah. so you'd need to set up a routine for swapping and recharging them. how is that done? and how much do they cost?
JELCRAWFORD
@JELCRAWFORD
Jun 07 2017 04:31
@annettemvalle - I trust some of the wise minds here helped you out with your BG data too old message - sorry, I was offline - seems like for just having been at it for a day, you are cooking with gas!
Cameron Chunn
@applehat
Jun 07 2017 04:48
@scottleibrand all charging is done externally in a charger. The AAA sized batteries are expensive. It would actually be cheaper to just make a pump case that used 18650 and a regulator. Tho then you have extra bulk.
Scott Leibrand
@scottleibrand
Jun 07 2017 04:51
I think they would still pay for themselves vs. buying lithium disposables, but my bigger concern is whether the battery would completely die (to the point where the pump couldn't even maintain basal) with no warning. at least if lithium disposables die to the point where the radio shuts off and it stops looping, it will still keep giving basal until you wake up.
rsilvers129
@rsilvers129
Jun 07 2017 05:11
I tested my enclosure with and without vents. When looping on battery, the internal temp went from 55C to 50C when vents were added. When charging, the internal temp went from 80C to 74C when vents were added. I updated my model on Thingiverse.
Dana Lewis
@danamlewis
Jun 07 2017 05:16
:+1:
rsilvers129
@rsilvers129
Jun 07 2017 05:19
I am back on dev now that I understand some or all or my stability problems were heat related. The setup script went well. Changing over worked the first time.
Whart do you all think of a watchdog process that reboots the system if the loop appears to not be working? And what do you think of temp monitoring being included and sending a pushover when close to the limit?
DaisyHK
@laurathiessen
Jun 07 2017 05:24
I was completing the bluetooth tethering step for my android with xdrip+ app to enable it to work offline by Bluetooth.. it got to the final step and asked me if i wanted to schedule openaps in cron... but before i could answer it went all crazy wanting to shut down..... what do I do know? reinstall the Bluetooth tethering and start from the beginning again?
image.png
Scott Leibrand
@scottleibrand
Jun 07 2017 05:26
@rsilvers129 if you could work on temperature alerting to pushover, I think that would be quite useful for a lot of people.
@laurathiessen you can ignore those reboot warnings and answer Y or N like you would if they hadn't shown up
that's a known issue related to re-running oref0-setup
rsilvers129
@rsilvers129
Jun 07 2017 05:28
@scottleibrand I put this into a file and run it from rc.local
tail -fn0 /var/log/syslog | \
while read line ; do
echo "$line" | grep "temperature above threshold"
if [ $? = 0 ]
then
curl -s --form-string "token=YOUR_PUSHOVER_TOKEN" --form-string "user=PUSHOVER_USER_KEY" --form-string "message=OpenAPS
: temperature above threshold." https://api.pushover.net/1/messages.json
sleep 900
fi
done
Scott Leibrand
@scottleibrand
Jun 07 2017 05:29
the trick is getting that into oref0-setup so it doesn't require any manual setup
rsilvers129
@rsilvers129
Jun 07 2017 05:29
The latest setup for dev asks for pushover keys
Scott Leibrand
@scottleibrand
Jun 07 2017 05:30
yep, so you'd definitely want to reuse those
rsilvers129
@rsilvers129
Jun 07 2017 05:31
Also sudo apt-get install lm-sensors
and sudo sensors-detect
Scott Leibrand
@scottleibrand
Jun 07 2017 05:31
I think the standard setup does lm-sensors now
what does sensors-detect get you?
does that log temps to syslog?
rsilvers129
@rsilvers129
Jun 07 2017 05:32
My script dumps it into syslog
I think detect probes once for what sensors are available
Scott Leibrand
@scottleibrand
Jun 07 2017 05:32
I don't think I've ever needed to install that
rsilvers129
@rsilvers129
Jun 07 2017 05:33
I don't know. I just found it somwhere and they said to do it
DaisyHK
@laurathiessen
Jun 07 2017 05:35
I needed to reboot it but I am confused as to what is my " If you have the “To run again with these same options” command-line from the last time you ran oref0-setup,"... how do i know if i ahve that command? this is my first time installing the blutooth tehter
image.png
ok.... neermind my putty thing just rebooted i guess and kicked m out and now i have to sign in again... i will test it out to confirm bluuezz is installed
image.png
nevermins it confirmed with the right version :)
DaisyHK
@laurathiessen
Jun 07 2017 05:46
ok my success line will not how up, have attempted a few times?
image.png
DaisyHK
@laurathiessen
Jun 07 2017 05:58
@scottleibrand any ideas?
Scott Leibrand
@scottleibrand
Jun 07 2017 06:04
what are you seeing?
DaisyHK
@laurathiessen
Jun 07 2017 06:12
@scottleibrand i apologize I was thinking I would see all the steps complete if it was successfull.... but I followed it and all the answers showed when I followed each individual step, my misunderstanding . Sory!
DaisyHK
@laurathiessen
Jun 07 2017 06:25
@scottleibrand I apologize but i attempted to now to launch the blutoth control panel, however when i went to pair it I had no idea which one to choose... how again do I find my rig numbers to locate when I scan on my phone? and how do I start this part over again from here?
image.png
Marco
@CaptainBalou
Jun 07 2017 07:40
Hello @danamlewis. I am currently deciding what CGM I should use. @ceben80 told me you are using Dexcom with an iPhone. Can you explain what hardware is involved and how the CGM data comes to OpenAPS? Perhaps also @scottleibrand knows...? ;-)
rsilvers129
@rsilvers129
Jun 07 2017 09:50
@laurathiessen on iPhone you go to settings then general then about. Go down to Bluetooth.
Marco
@CaptainBalou
Jun 07 2017 11:48
@rsilvers129 Nice case. New version with ventilation capabilities is a good idea. Can you post a link from thingiverse?
Marco
@CaptainBalou
Jun 07 2017 12:15
@rsilvers129 Forget it. I found it. thumbs up
Jennifer Montbach
@jenm999
Jun 07 2017 12:40
Crap. What have I done?
image.png
image.png
I think all you west coasters are asleep. :)
sdneufer
@sdneufer
Jun 07 2017 12:53
@jenm999 Did you try rebooting the rig? If on an edison you can login as root and type shutdown -r now
on a pi you would need to use sudo shutdown -r now
Jennifer Montbach
@jenm999
Jun 07 2017 13:05
@sdneufer Yep, both manual and using reboot command in putty
rsilvers129
@rsilvers129
Jun 07 2017 13:05
@CaptainBalou Dexcom is the CGM to use. Your choices are G5 to an iPhone l, G4 to a receiver to USB. Or either to an Android running xDrip.
Jennifer Montbach
@jenm999
Jun 07 2017 13:06
Hubs just removed the index.lock file after googling the error. Rebooting now. Fingers crossed. Not sure what caused this
Marco
@CaptainBalou
Jun 07 2017 13:08
@jenm999 I saw someone aswering some days ago: can happen when your rig goes off because of no battery while some git processes were still running.
@jenm999 But I am sure there are a lot of other reasons available. :-)
@rsilvers129 G5 uploads to an iPhone directly? Via BT pairing or what is the way they do it?
Jennifer Montbach
@jenm999
Jun 07 2017 13:10
@CaptainBalou I was screwing around with the preferences.json file to widen the autosens margins. I'm not running autosens yet but thought it might give me more insight in autotune. It gave me a blank output. (I tried 3 and .1 just for yuks) - I wonder if that could have borked it somehow?
@CaptainBalou Of course now the rig is at home and kid is at school with pump only. I may let it ride today and see how basal rates are without OpenAPS intervention...
rsilvers129
@rsilvers129
Jun 07 2017 13:11
Yes. BT to an iPhone. But then iPhone to Dexcom. And Dexcom to Nightscout. And rig sees data over wifi or (Bluetooth pairing) to Nightscout.
sdneufer
@sdneufer
Jun 07 2017 13:12
removing the index.lock was my next suggestion... I was hoping it would be removed on the startup. My explorer is an older board and it gets hot then won't let me login until it cools down.
Did you save an older copy of your preferences.json before you changed it. May want to put it back to see if that fixes your problem.
Jennifer Montbach
@jenm999
Jun 07 2017 13:14
@sdneufer Rebooting did not seem to remove the file. So we did it manually. I did save and replace preferences.json with the correct values.
sdneufer
@sdneufer
Jun 07 2017 13:26
have you tried reseting the edison radio. I am trying to find the instructions...
Jennifer Montbach
@jenm999
Jun 07 2017 13:27
Now that the pump is not with it I can't tell if it's working but I think it is. We're going to drop it off at school shortly and hope that it picks up again.
sdneufer
@sdneufer
Jun 07 2017 13:29
Time for a second edison. one to try new things on... I am trying to find the time to get my second working as it is a real pain when I end up killing it for a few hours...
good luck :-)
Jennifer Montbach
@jenm999
Jun 07 2017 13:31
You too, thanks for the troubleshooting!
Lin
@denglfddd
Jun 07 2017 14:12
Who knows how to remove all the data on the drill command
PopcornPam
@PopcornPam_twitter
Jun 07 2017 15:38
Hi all, still trying to figure out my rigs ip address so I can update wifi on the go. inet crashes everytime i try to scan, and ip scanner says no networks, despite my phone being bluetooth connected to rig. Help?
Scott Leibrand
@scottleibrand
Jun 07 2017 16:16
@denglfddd I don't understand that question.
Lin
@denglfddd
Jun 07 2017 16:18
@scottleibrand I seem to have deleted some important things and are trying to refresh it again
Scott Leibrand
@scottleibrand
Jun 07 2017 16:18
@CaptainBalou the G4 Share receiver also connects to the iPhone via Bluetooth, similar to how the G5 transmitter does. Both upload to Dexcom's Share servers, where the data can be automatically pulled in by Nightscout without going through a rig. We usually have our rigs pull BG data from NS, and use the plugged-in receiver over USB OTG for backup purposes and to allow us to keep looping during the 2 hour sensor warmup.
@denglfddd Any idea what you deleted?
PopcornPam
@PopcornPam_twitter
Jun 07 2017 16:21
Is there a way to use the command line (when home on wifi) to get the ip address of the rig so I can set up terminus on my iphone? All I see are two things, one 'vendor unknown', the other is 'intel corporate" when I try to use network scanner on inet. Do I need the pro version?
Lin
@denglfddd
Jun 07 2017 16:21
@scottleibrand I can only log in as ROOT drilling rig, all other instructions do not work l...
katie disimone
@Kdisimone
Jun 07 2017 16:27
@denglfddd sounds like you don't have a loop going if l doesn't work
Pam...I tagged you in a scanner app yesterday that works. Did you try that?

And yes...you could use a screen/serial connection (cable your rig to your computer via UART port) and use wifi

Perhaps easier is simply to install Papertrail on your rig and simply read the IP address in the logs.

Lin
@denglfddd
Jun 07 2017 16:31
@Kdisimone sorry,i dont know what app you said
Jennifer Montbach
@jenm999
Jun 07 2017 16:32
@Kdisimone I have tried to log into my rig using its IP as given by paper trail with no luck. Could that be a restriction of the network he's on?
katie disimone
@Kdisimone
Jun 07 2017 16:33
@denglfddd I was speaking to Pam. My mobile app won't let me tag her

@jenm999 my experience is those IP address are always correct. (assuming you aren't inadvertently trying to use a public IP address...which are reported too. You want to use the local IP address)

The error would likely be that your device you are trying to connect with is not actually on that wifi network listed. When your device isn't on the same network...it won't connect.


Jun 07 09:32:02 edison3 network.log:  At Wed Jun  7 09:32:02 PDT 2017 my local IP is: 10.250.191.254
Jun 07 09:32:03 edison3 network.log:  At Wed Jun  7 09:32:02 PDT 2017, my wifi network name is Paso Schools, and my public IP is: 207.62.28.250
katie disimone
@Kdisimone
Jun 07 2017 16:39
@jenm999 what's the situation you are trying to do? Laptop while he's at school and you are at school too? Or using termius app? Can you give more details
Diabetic_Dude
@diabetic_dude_twitter
Jun 07 2017 16:58
Looks like Pebble twos are on clearance at Walmart local stores only https://slickdeals.net/f/10225348-pebble-2-hr-30-walmart-b-m-ymmv. They are 30 dollars
Jennifer Montbach
@jenm999
Jun 07 2017 16:59
@Kdisimone It would be nice to fix problems while he's at school, yes. If that's not possible that's OK. My husband is thinking he could use some kind of VPN trickery to log into the rig when not on the same network. Not a critical thing, just would be helpful from time to time.
Like today, when somehow I screwed something up royally while experimenting with autotune (I tried making autosens adjustments wider for the purposes of autotune - I think some problems are solved with changing rates, others with the time you change from rate A to B esp. if the difference is more than 20%)
Right now the pump and rig are talking but not looping, I think because of this error:
image.png
image.png

OOf, hard to read. Try this:

Jun 07 12:49:10 lucas pump-loop.log: Could not parse input data: [SyntaxError: /root/myopenaps/monitor/iob.json: Unexpected end of input]

Jun 07 12:48:57 lucas pump-loop.log: glucose.json newer than temp_basal.json
Scott Leibrand
@scottleibrand
Jun 07 2017 17:10
@jenm999 to figure out why the iob.json is empty, you'll need to run that report manually (and possibly drill down from there), or inspect the various other files used as input to calculate-iob.
katie disimone
@Kdisimone
Jun 07 2017 17:10
@jenm999 yes...getting into a remote rig in that situation would require a VPN be set up. FWIW, I was thinking I wanted a vpn really early on, but as we setttled in and got used to the system...we don't feel need for that anymore. It takes a few weeks to settle in for sure.
And for the first few weeks, rebooting is definitely a friend
Scott Leibrand
@scottleibrand
Jun 07 2017 17:11
@denglfddd you'll need to be more specific: paste in exactly what you're seeing so we can help you. https://diyps.org/2017/03/19/tips-for-troubleshooting-diy-diabetes-devices-openaps-or-otherwise/ has some guidelines on the kind of info we need to help troubleshoot
Jennifer Montbach
@jenm999
Jun 07 2017 17:14
@scottleibrand Is there a way just to reset everything as if I'm setting it up for the first time? rerun the script? I'm sure it's because I was fiddling with the preferences.json and adjusting basal for teh afternoon and generally throwing too much information at it. I have the rig with me now (though not the kid or the pump) and can just start from scratch.
Scott Leibrand
@scottleibrand
Jun 07 2017 17:22
yeah, for that kind of thing just re-running oref0-setup (probably using oref0-runagain) is easiest
Jennifer Montbach
@jenm999
Jun 07 2017 17:25
Awesome, thanks.
ejoe132
@ejoe132
Jun 07 2017 17:59
When setting temp targets in NS, I have always just left it on eating soon mode, and set the target # and duration as needed whether it be for eating soon or activity. Is there any advantage or does it do anything different if I set the type for eating soon or activity?
PopcornPam
@PopcornPam_twitter
Jun 07 2017 18:14
@Kdisimone , I was trying to find that post from yesterday and couldn't locate it, could you remind me of the app name?
So it seems that I have the right ip address (via papertrail), but can't get terminus to connect
katie disimone
@Kdisimone
Jun 07 2017 18:16
@PopcornPam_twitter Can you post a screen shot of your Host setup for the Termius app? Maybe a typo there?
@PopcornPam_twitter Net Analyzer
PopcornPam
@PopcornPam_twitter
Jun 07 2017 18:20
net analyzer works great! but it shows the same ip address I had put in there... trying to get the pic from phone to computer when on different networks
Dana Lewis
@danamlewis
Jun 07 2017 18:29
@ejoe132 nah, just probably ease of looking back at different types, but it doesn’t matter as long as you set the target # from openaps perspective
PopcornPam
@PopcornPam_twitter
Jun 07 2017 18:39
image.png
katie disimone
@Kdisimone
Jun 07 2017 18:46
@PopcornPam_twitter ODD…that looks all correct. Maybe erase and try your password again?
Also @PopcornPam_twitter I’ve recently started using another app for SSH and am really liking it (even better than Termius now). It’s called SimpleSSH.
ejoe132
@ejoe132
Jun 07 2017 18:54
@danamlewis Ok thank you!
PopcornPam
@PopcornPam_twitter
Jun 07 2017 18:55
I have erased and reinstalled the app a few times, will try simplessh
garykidd
@garykidd
Jun 07 2017 19:08
@all/ any idea why I get a 'cannot find a bored instance' when trying to upload an image here?
Dana Lewis
@danamlewis
Jun 07 2017 19:10
@garykidd no idea
garykidd
@garykidd
Jun 07 2017 19:11
huh...weird.
thx @danamlewis
Dana Lewis
@danamlewis
Jun 07 2017 19:11
For anyone who’s wondering what we’re working on to get dev to master, we are working on (https://github.com/openaps/oref0/pull/424#issuecomment-306895549) before final testing rounds.
katie disimone
@Kdisimone
Jun 07 2017 19:31
@scottleibrand I don’t think I get lm-sensors as part of standard install. I just checked on mine.
@rsilvers129 I’m just jumping in on this convo. Let me know where you are on PRs to get this into the oref0 and setup…i’ll work with you
@rsilvers129 Yeah, I agree with scott….I haven’t had to use sudo sensors-detect to log my temps in the past
katie disimone
@Kdisimone
Jun 07 2017 19:38
@scottleibrand and @rsilvers129 I take it back…my needs may be more simplified. I can see sensors uploaded to papertrail already.
Screen Shot 2017-06-07 at 12.39.06 PM.png
I’m goign to set up instructions on how to use Papertrail to send pushover messages…I think that would be quite useful
Scott Leibrand
@scottleibrand
Jun 07 2017 19:42
@Kdisimone huh, I thought we added it, but I don't see it either. we probably should PR that in to the list of packages we install
katie disimone
@Kdisimone
Jun 07 2017 19:42
That’s in openaps yes?
katie disimone
@Kdisimone
Jun 07 2017 19:43
you are so quick :smile:
Scott Leibrand
@scottleibrand
Jun 07 2017 19:43
I had the same question before you asked it. :)
Diadon81
@Diadon81
Jun 07 2017 19:55
Dears I have a question about CSF? What kind of units it used? gram per 1u of insulin?
Dana Lewis
@danamlewis
Jun 07 2017 19:56
CSF is a ratio of carb ratio to ISF. You don’t need to use it for anything.
Diadon81
@Diadon81
Jun 07 2017 19:57
Am I right, that Carb Ratio is a gram per 1u of insulin?
Scott Leibrand
@scottleibrand
Jun 07 2017 19:58
yes, CR is g/U
Diadon81
@Diadon81
Jun 07 2017 19:58
Clear.
Scott Leibrand
@scottleibrand
Jun 07 2017 19:58
ISF is mg/dL/U, so CSF is mg/dL BG rise expected per g of carb eaten.
Diadon81
@Diadon81
Jun 07 2017 19:59
Ok, now I am understand the terminology.
Look at my basal suggestions. It looks strange for me, that my basal at 23:00 and 00:00 the same with my pump settings and not adjusted at all. Is it normal or some kind of bug. I am using dev branch.
Basal Profile  |          |
  00:00        | 1.500    | 1.500
  00:30        |          |
  01:00        |          | 1.490
  01:30        |          |
  02:00        |          | 1.465
  02:30        |          |
  03:00        |          | 1.429
  03:30        |          |
  04:00        |          | 1.392
  04:30        |          |
  05:00        |          | 1.376
  05:30        |          |
  06:00        |          | 1.388
  06:30        |          |
  07:00        |          | 1.394
  07:30        |          |
  08:00        |          | 1.420
  08:30        |          |
  09:00        |          | 1.552
  09:30        | 1.5      |
  10:00        |          | 1.597
  10:30        |          |
  11:00        |          | 1.593
  11:30        |          |
  12:00        |          | 1.474
  12:30        |          |
  13:00        |          | 1.474
  13:30        |          |
  14:00        |          | 1.480
  14:30        |          |
  15:00        |          | 1.480
  15:30        |          |
  16:00        |          | 1.475
  16:30        |          |
  17:00        |          | 1.450
  17:30        |          |
  18:00        |          | 1.407
  18:30        |          |
  19:00        |          | 1.274
  19:30        |          |
  20:00        |          | 1.216
  20:30        |          |
  21:00        |          | 1.258
  21:30        |          |
  22:00        |          | 1.393
  22:30        |          |
  23:00        |          | 1.500
  23:30        | 1.5      |
Dana Lewis
@danamlewis
Jun 07 2017 20:04
@Diadon81 usually it means there’s not enough data for that time period to calculate adjustments for
Diadon81
@Diadon81
Jun 07 2017 20:05
How it can be possible? I am using CGM 24/7
Dana Lewis
@danamlewis
Jun 07 2017 20:05
because you have a lot of carb data, and there’s not enough basal-driven data to tune the basal then
(later dinner effect, et.)
Diadon81
@Diadon81
Jun 07 2017 20:06
hmm.. I don't eat after 18:00 :)
Dana Lewis
@danamlewis
Jun 07 2017 20:06
you can dig into the logs and see how it’s tuning those hours to see what it’s doing and why
Diadon81
@Diadon81
Jun 07 2017 20:06
ok, I will try to investigate.
by the way, when I change my bolus wizard from exch. to grams I fixed COB and UAM prediction
just for your information
Dana Lewis
@danamlewis
Jun 07 2017 20:08
ok great thanks for confirming - it will help us troubleshoot with people faster next time, too :) if we spot carbs not making it from the pump!
rsilvers129
@rsilvers129
Jun 07 2017 20:15
Today I had three slices of large sausage pizza (99 grams carb and lots of fat). Never went over 136 using oref1.
3-slices-sausage-pizza.PNG
Diadon81
@Diadon81
Jun 07 2017 20:17
I am waiting for FIASP. For me it's very interesting for me, how it improve my compensation
I have a small hope to don't have a bolus at all with FIASP.
Andrew Baugh
@baughaw
Jun 07 2017 20:18
@rsilvers129 Looks awesome, can you tell me why you entered the few extra 5g of carbs?
rsilvers129
@rsilvers129
Jun 07 2017 20:19
@baughaw I got a pushover requesting that I eat 3 grams of carb. Oref1 can do that to keep you from going low. I had a bag of cookies that were 2.5 grams each. I ate two of them, and then logged 5 grams of carb.
Andrew Baugh
@baughaw
Jun 07 2017 20:21
ah that makes, thanks for the info.
rsilvers129
@rsilvers129
Jun 07 2017 20:21
My auto-tune recommended carb-ratio is about 8.0. I had my pump set to 7.5, so I had a bit more downward pressure than I should have had, and so the rig was trying to keep me higher at times. But it sure seems like a decent A1c is possible without eating low-carb all the time. And I am now sold on oref1 over oref0 now that I know my rig was hanging from overheating, and also seeing that the SMBs are not instead of high-temps but in addition to them.
Andrew Baugh
@baughaw
Jun 07 2017 20:24
👍
garykidd
@garykidd
Jun 07 2017 20:27
wondering if others are having rthe 'Could not get subg_rfspy state or version' error routinely like I am. Any thoughts on what is driving this?
Scott Leibrand
@scottleibrand
Jun 07 2017 20:27
@rsilvers129 there have also been a couple of minor tweaks to oref1 since you first tried it, which might be helping at the margins
rsilvers129
@rsilvers129
Jun 07 2017 20:28
@garykidd I used to get that a lot. One thing to try is to unplug the battery, and replug it in, and try again.
dan lightner
@danimaniac
Jun 07 2017 20:28

My last a1c was 6.0 (before using OpenAPS) and while I limited the carb intake, I certainly ate pizza and Dairy Queen Blizzards whenever we wanted. @rsilvers129

But it sure seems like a decent A1c is possible without eating low-carb all the time.

dan lightner
@danimaniac
Jun 07 2017 20:34
Next a1c will be my first while using OpenAPS. I actually expect it to be a little higher than 6.0 because i have taken advantage of the freedoms OpenAPS has given me. I eat more carbs now, more often, and just don't worry about it much. I still expect 6.4 - 6.6 maybe.
marafie
@marafie
Jun 07 2017 20:42
Were can I download xdripaps?
I think I just answered you on Fbk, too - I’d make sure your loop is working with online BGs first - if it’s successfully looping pulling BGs from NS, then you can next do xdripAPS for offline looping.
garykidd
@garykidd
Jun 07 2017 20:46
@rsilvers129 strange because I actually have my battery soldered to explorer without cable to save some space
marafie
@marafie
Jun 07 2017 20:54
D
Thanks
Dana Lewis
@danamlewis
Jun 07 2017 20:56
:+1:
Tony Zarro
@tzarro
Jun 07 2017 21:09
hey y'all, I'm afraid I'm stumped on something which is probably really simple...but after searching Gitter, I need to ask for help: my rig stopped connecting to any and all of my wireless networks, but when I go to attempt to reinstall I find that even when I'm tethered to my PC via USB I still don't have internet connectivity...pinging www.google.com (or any other site) yields "unknown host". Any ideas on where to look next?
marafie
@marafie
Jun 07 2017 21:10
Can I used 3000mah battery instead of 2000mah
garykidd
@garykidd
Jun 07 2017 21:10
@marafie yes
but it'll last longer
assuming it's still 3.7v battery, of course.
marafie
@marafie
Jun 07 2017 21:11
The male connector is larger than the one on the explorer board
So I guess I just need to replace jt5
garykidd
@garykidd
Jun 07 2017 21:12
sounds like you need to change the connector...be sure to wire correctly...you can invert the voltage and cause yourself a big headache.
@tzarro assuming you already rebooted and hard reset your rig?
Tony Zarro
@tzarro
Jun 07 2017 21:13
@garykidd yes, many many times :)
garykidd
@garykidd
Jun 07 2017 21:14
and your wifi is up because other devices on same network have no issues, correct?
Tony Zarro
@tzarro
Jun 07 2017 21:15
yes, other devices can access my wifi...and this is happening with three different wifi networks...
Scott Leibrand
@scottleibrand
Jun 07 2017 21:16
check your wifi logs and see if the rig is even associating to your SSID, or if it's erroring out
garykidd
@garykidd
Jun 07 2017 21:16
and you're definitely trying to connect rig to same wifi nework that your computer terminal is on
?
marafie
@marafie
Jun 07 2017 21:16
@garykidd thanks
Tony Zarro
@tzarro
Jun 07 2017 21:16
you mean network.log?
Scott Leibrand
@scottleibrand
Jun 07 2017 21:16
that's one good place to start, yes
Tony Zarro
@tzarro
Jun 07 2017 21:16

Starting oref0-online.
At Wed Jun 7 17:15:02 EDT 2017 my local IP is:
At Wed Jun 7 17:15:02 EDT 2017, my wifi network name is , and my public IP is:
Error, cycling networking
Stopping networking (via systemctl): networking.service.
Starting networking (via systemctl): networking.service.
and getting new wlan0 IP

At Wed Jun 7 17:15:56 EDT 2017, my wifi network name is , and my public IP is:
At Wed Jun 7 17:15:56 EDT 2017 my public IP is:
Error, connecting BT to A8:9F:BA:E3:5C:AD, getting bnep0 IP

At Wed Jun 7 17:15:57 EDT 2017, my wifi network name is , and my public IP is: Finished oref0-online.

Starting oref0-online.
At Wed Jun 7 17:16:02 EDT 2017 my local IP is:
At Wed Jun 7 17:16:02 EDT 2017, my wifi network name is , and my public IP is:
Error, cycling networking
Stopping networking (via systemctl): networking.service.
Starting networking (via systemctl): networking.service.

Scott Leibrand
@scottleibrand
Jun 07 2017 21:17
my wifi network name is , means you're not connected to a wifi network
Tony Zarro
@tzarro
Jun 07 2017 21:17
not sure where to look deeper...are there lower-level logs than network.log?
Scott Leibrand
@scottleibrand
Jun 07 2017 21:17
yeah, I think some of it goes to syslog
Tony Zarro
@tzarro
Jun 07 2017 21:17
ok
marafie
@marafie
Jun 07 2017 21:21
Is running g the script with BY options takes a long time ?
By
t
BT
Scott Leibrand
@scottleibrand
Jun 07 2017 21:21
autocorrect FTW. :)
yes, it takes about 45m to compile bluez the first time you run oref0-setup with the bluetooth options
marafie
@marafie
Jun 07 2017 21:22
Oooh
Marco
@CaptainBalou
Jun 07 2017 21:47
@scottleibrand Cool, thanks for this information. I try to make my decision... But whatever it will be: there is a huge problem getting sensors in Germany these days. They told me that I probably have to wait 3 months or more to get my first sensor. Ridiculous.
marafie
@marafie
Jun 07 2017 21:50
Do I need to enable any setup in the 722 model ? Like letting the radio on?
Dana Lewis
@danamlewis
Jun 07 2017 21:50
@marafie that shouldn’t matter - but how close is your pump to the rig?
the usual issue is that basals are on % instead of absolute, but yours are on absolute already.
marafie
@marafie
Jun 07 2017 21:51
It's like less than 10 cm away
Dana Lewis
@danamlewis
Jun 07 2017 21:51
k. do you see any “mmtune” results in your logs with numbers?
marafie
@marafie
Jun 07 2017 21:54
Mmtune is which file?
Dana Lewis
@danamlewis
Jun 07 2017 21:54
you should see it in the logs, something like:
mmtune: "916.612", 3, -65 waiting for 10 second silence before continuing Radio ok. Listening: .No pump comms detected from other rigs
marafie
@marafie
Jun 07 2017 22:02
Oops no idea what happens
Fixing radio error will reboot
Dana Lewis
@danamlewis
Jun 07 2017 22:08
normal - it’ll self-resolve
marafie
@marafie
Jun 07 2017 22:11
It gave me something related to python error I am setting it again
Dana Lewis
@danamlewis
Jun 07 2017 22:15
@marafie ignore that and just hit y
marafie
@marafie
Jun 07 2017 22:21
I did and now when opening the log file it gives other errors ,
I mentioned them in Facebook for you
Dana Lewis
@danamlewis
Jun 07 2017 22:21
what kind of rig are you using? Edison/Explorer Board, or something else?
marafie
@marafie
Jun 07 2017 22:21
Yes
As you mentioned
Dana Lewis
@danamlewis
Jun 07 2017 22:21
and did you say yes for having a WW (worldwide) pump?
marafie
@marafie
Jun 07 2017 22:21
We
Yes
722wws
Dana Lewis
@danamlewis
Jun 07 2017 22:22
k. can you repost that last picture here so others can take a look at it, too? (drag and drop into Gitter)
marafie
@marafie
Jun 07 2017 22:23
I bought them from Kiev for 450 USD
rsilvers129
@rsilvers129
Jun 07 2017 22:24
Is there a way to post a photo from an iPhone to Gitter?
Dana Lewis
@danamlewis
Jun 07 2017 22:24
@rsilvers129 not easily, other than sticking it in dropbox or a file sharing site and then pasting the URL in
@logichammer if you’re setting up pancreabble, can you provide some feedback on https://github.com/openaps/docs/pull/741/files, plus anything else you figure out for setting up Pancreabble?
Cameron Chunn
@applehat
Jun 07 2017 22:29
I need to revisit Pancreabble. I have that thing sitting on my desk
Dana Lewis
@danamlewis
Jun 07 2017 22:30
@applehat same goes for you then :D and anyone else tackling it lately/now/soonish
Cameron Chunn
@applehat
Jun 07 2017 22:30
I need to get a laptop so I can work on stuff while not ostracizing my family. =P
Dana Lewis
@danamlewis
Jun 07 2017 22:30
lol. not lol. but lol.
Cameron Chunn
@applehat
Jun 07 2017 22:31
That really is my biggest reason I don't get stuff done at home. Dont like locking myself away in my office and ignoring my kids.
Dana Lewis
@danamlewis
Jun 07 2017 22:33
:+1:
marafie
@marafie
Jun 07 2017 22:37
pump1.png
pump1.png
this is from now
marafie
@marafie
Jun 07 2017 22:45
this was the error before it
pump2.png
@danamlewis no marine in the the 1 image
garykidd
@garykidd
Jun 07 2017 22:47
regarding remainingCarbsCap Is the rate of assumed absorption of carbs (in the absence of overt absorption) assumed to be linear over a 4-hour period.
katie disimone
@Kdisimone
Jun 07 2017 22:54
So my explorer board is toast I think. Randomly turning off several times a day. No apparent reason. Replaced lipo. Removed lipo, and tried wall plug only. Changed edison boards. Definitely seems to be the explorer board. Went into some of the logs to see what’s gone on….what is up with this random date switch?!
Jun  7 15:02:01 edisonSMB CRON[13830]: (root) CMD (cd /root/myopenaps && ps aux | grep -v grep | grep -q oref0-truncate-git-history || oref0-truncate-git-history)
Jun  7 15:02:01 edisonSMB CRON[13832]: (root) CMD (ps aux | grep -v grep | grep -q "oref0-online D0:25:98:07:28:CA" || oref0-online D0:25:98:07:28:CA 2>&1 >> /var/log/openaps/network.log)
Jun  7 15:02:01 edisonSMB CRON[13767]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:02 edisonSMB CRON[13766]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:02 edisonSMB CRON[13764]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:02 edisonSMB CRON[13762]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:02 edisonSMB CRON[13761]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:03 edisonSMB CRON[13758]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:03 edisonSMB CRON[13768]: (CRON) info (No MTA installed, discarding output)
Jun  7 15:02:07 edisonSMB CRON[13760]: (CRON) info (No MTA installed, discarding output)
Dec 31 16:00:36 edisonSMB rsyslogd: [origin software="rsyslogd" swVersion="8.4.2" x-pid="356" x-info="http://www.rsyslog.com"] start
Dec 31 16:00:36 edisonSMB systemd-modules-load[112]: Inserted module 'bcm_bt_lpm'
Dec 31 16:00:36 edisonSMB systemd-modules-load[112]: Inserted module 'bcm4334x'
Dec 31 16:00:36 edisonSMB systemd-modules-load[112]: Inserted module 'g_multi'
Dec 31 16:00:36 edisonSMB systemd-modules-load[112]: Inserted module 'uvcvideo'
Dec 31 16:00:36 edisonSMB systemd-modules-load[112]: Failed to find module 'ftdi_sio'
Dec 31 16:00:36 edisonSMB systemd[1]: systemd-modules-load.service: main process exited, code=exited, status=1/FAILURE
Dec 31 16:00:36 edisonSMB systemd[1]: Failed to start Load Kernel Modules.
Dec 31 16:00:36 edisonSMB systemd[1]: Unit systemd-modules-load.service entered failed state.
Dec 31 16:00:36 edisonSMB systemd[1]: Started Load/Save Random Seed.
Dec 31 16:00:36 edisonSMB systemd[1]: Started Create Static Device Nodes in /dev.
Dec 31 16:00:36 edisonSMB systemd[1]: Starting udev Kernel Device Manager...
Dec 31 16:00:36 edisonSMB systemd[1]: Starting Apply Kernel Variables...
Dec 31 16:00:36 edisonSMB systemd[1]: Mounted /tmp.
Dec 31 16:00:36 edisonSMB systemd[1]: Mounted Configuration File System.
Dec 31 16:00:36 edisonSMB systemd[1]: Mounted FUSE Control File System.
Dec 31 16:00:36 edisonSMB systemd[1]: Started udev Kernel Device Manager.
Dec 31 16:00:36 edisonSMB systemd[1]: Started Apply Kernel Variables.
Dec 31 16:00:36 edisonSMB systemd[1]: Found device /dev/ttyMFD2.
Dec 31 16:00:36 edisonSMB systemd[1]: Starting system-systemd\x2drfkill.slice.
Dec 31 16:00:36 edisonSMB systemd[1]: Created slice system-systemd\x2drfkill.slice.
Dec 31 16:00:36 edisonSMB systemd[1]: Starting Load/Save RF Kill Switch Status of rfkill0...
Dec 31 16:00:36 edisonSMB systemd[1]: Starting Copy rules generated while the root was ro...
Dec 31 16:00:36 edisonSMB systemd[1]: Started Copy rules generated while the root was ro.
Dec 31 16:00:36 edisonSMB systemd[1]: Started Load/Save RF Kill Switch Status of rfkill0.
Dec 31 16:00:36 edisonSMB systemd[1]: Found device /dev/mmcblk0p7.
Dec 31 16:00:36 edisonSMB systemd[1]: Starting File System Check on /dev/mmcblk0p7...
Dec 31 16:00:36 edisonSMB systemd[1]: Found device /dev/mmcblk0p10.
Dec 31 16:00:36 edisonSMB systemd[1]: Starting File System Check on /dev/mmcblk0p10...
Dec 31 16:00:36 edisonSMB systemd-fsck[165]: /dev/mmcblk0p10: recovering journal
marafie
@marafie
Jun 07 2017 22:54
It worked
Thanks
katie disimone
@Kdisimone
Jun 07 2017 22:55
Any ideas on where else I should look?
Cameron Chunn
@applehat
Jun 07 2017 22:56
@Kdisimone Dec 31 1969 is often the date that is calculated when the Epoch time is read as 0
So the CMOS (do we have CMOS?) is reporting wrong
katie disimone
@Kdisimone
Jun 07 2017 22:57
Greek to me. sorry. I don’t speak that.
AND…it just rebooted itself again. at 15:55
Jun 07 15:55:47 edisonSMB systemd-fsck: CP437: Invalid argument
Jun 07 15:55:47 edisonSMB systemd-fsck: fsck.fat 3.0.27 (2014-11-12)
Jun 07 15:55:47 edisonSMB systemd-fsck: 0x25: Dirty bit is set. Fs was not properly unmounted and some data may be corrupt.
Jun 07 15:55:47 edisonSMB systemd-fsck: Automatically removing dirty bit.
Jun 07 1
Cameron Chunn
@applehat
Jun 07 2017 22:58
That looks like disk corruption
Would explain your Real Time Clock getting reset to 0 as well.
katie disimone
@Kdisimone
Jun 07 2017 22:58
Is the explorer board hosing my edisons?
Cameron Chunn
@applehat
Jun 07 2017 22:59
Im not sure how it would be causing that issue
katie disimone
@Kdisimone
Jun 07 2017 22:59
This is a different edison than yesterday when we were having the same issues.
Cameron Chunn
@applehat
Jun 07 2017 22:59
Hmm
garykidd
@garykidd
Jun 07 2017 23:00
@Kdisimone wonder if re-flashing might be called for.....
katie disimone
@Kdisimone
Jun 07 2017 23:01
reflash fix...
oh you just read my mind…i wonder if it would help. I just feel like it is the explorer board since this happened on other edison all day the last two days. Other edison is now fine with a different explorer board
and it has failed again. ARGH
garykidd
@garykidd
Jun 07 2017 23:02
I feel ya
I keep getting dreaded rfspy state/version errors that causes me to have to re-flash radio
Scott Leibrand
@scottleibrand
Jun 07 2017 23:16
@garykidd yes. the currently observed absorption is decayed linearly to zero over however long it takes to absorb all the COB, and if that extends beyond 4h, then the remainingCarbs not projected to absorb over 4h are applied as a constant rate of absorption for the full 4h, in addition to whatever small amount of observed absorption was already allocated
so in the simple case of no observed absorption, then if remainingCarbsFraction is 1, all of the COB will be projected to absorb evenly over 4 hours
that means we project a sudden increase within the next 5m to that level of absorption, and then a sudden drop-off at the 4h mark, neither of which are all that plausible, but given that we're averaging COB over 4h, the discontinuity is usually fairly small, and the averages work pretty well for predicting a reasonable minPredBG and eventualBG.
katie disimone
@Kdisimone
Jun 07 2017 23:19
Ok, trying the “corrupted” edison (the one that has been failing) on a different explorer board…figure this will confirm that it is the explorer board. If the edison is corrupted (vs the explorer board failing), then I expect this should fail soon. So far it is working fine
PopcornPam
@PopcornPam_twitter
Jun 07 2017 23:40
So I have been going pretty high (between 250-300) after eating, even when accurately entering carbs with bolus wizard. I am running oref 1 with all the new features enabled. I think my rates are all good, but definately not responding well to boluses. Thoughts?
katie disimone
@Kdisimone
Jun 07 2017 23:41
cat-pref @popcornpam_twitter
perhaps some of your settings are too conservative?
PopcornPam
@PopcornPam_twitter
Jun 07 2017 23:42
as in, look at my preferences? I have been tweaking them, and upped my max iob to 1, and in addition to the highs, was going low on the rebound. dropped to .9 and it took away the lows
I will admit to not fully understanding the snooze settings
I also upped the remaining carb cap to .2
katie disimone
@Kdisimone
Jun 07 2017 23:43
and when did you last freshly pull from dev branch? There were some pretty significant updates to the algorithm that have helped us not go high after meals…if you haven’t updated your oref0 dev since June 5th, I’d recommend doing so
PopcornPam
@PopcornPam_twitter
Jun 07 2017 23:43

I just (like just now) ran mkdir -p ~/src; cd ~/src && git clone -b dev git://github.com/openaps/oref0.git || (cd oref0 && git checkout dev && git pull)

cd ~/src/oref0 && npm run global-install

katie disimone
@Kdisimone
Jun 07 2017 23:44
ok…if you ran that just now, it would be the most current.
PopcornPam
@PopcornPam_twitter
Jun 07 2017 23:45
can anyone explain this a bit more? I have read teh docs, but still don't really understand its function or how ti works
"bolussnooze_dia_divisor"
PopcornPam
@PopcornPam_twitter
Jun 07 2017 23:52
Also, is there a way to enable autotune without re-installing? I can't get my runagain code to work
live4sw
@live4sw
Jun 07 2017 23:56
Random question - when you treat a low with carbs, do you do bolus wizard and input the carbs and bolus 0.1U so that it registers? I realized recently that since I haven't been doing that, it's likely distorting my autotune (which I run manually on a VM).