These are chat archives for nightscout/intend-to-bolus

7th
Jul 2017
Thacher
@thacherT1D
Jul 07 2017 00:39 UTC
advice on charging an extra lipo battery? do I need another board?
LilDucky
@LilDucky
Jul 07 2017 00:43 UTC
Can get lots of small lipo chargers cheap on eBay. Also some programmable ones available from hobby stores that can test capacity.
Cameron Chunn
@applehat
Jul 07 2017 01:08 UTC
adafruit / sparkfun / amazon / ebay / aliexpress all sell USB lipo chargers
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 01:48 UTC
Hi everypony, maybe someone here can give me advice. I'm trying to run openasp from my ubuntu linux. Edison/Explorer board, Dexcom G5, 722 pump. I'm stuck at the moment of communications with pump. I did run oref0 sh script. I believe i aslo did add my pump here: "openaps device add pump medtronic **". But when I try to check if it working by typing "openaps use pump model" I get this: "serial.serialutil.SerialException: Attempting to use a port that is not open"
Dana Lewis
@danamlewis
Jul 07 2017 01:49 UTC
You don't need to manually add the pump device
The script does it for you
Make sure you say yes in the script to explorer board so it sets up the right port for you
(It won't hurt to rerun if you can't remember if you said yes to that)
Also, just type l to watch the logs and see what it's doing after running setup
Only need to run manual commands if it doesn't work after ~20+ minutes, and you'll have to stop cron before you do that if so.
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 01:54 UTC
Wow, it was fast, thanks Dana
I believe that I did answer "y" for explorer board question, but i better go rerun the script
Dana Lewis
@danamlewis
Jul 07 2017 02:00 UTC
:+1: yup, rerun and then hit l and watch the logs. Remember it'll take a good 15-20 minutes to pull a full pump history before it runs, so don't worry about troubleshooting until after 20
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 02:06 UTC
ok, sure!
should i do something on pump side?
i saw "remote options" that can be turned on (add it / delete id / review ad) or off
Cameron Chunn
@applehat
Jul 07 2017 02:08 UTC
Those are just for the little handheld remotes
OpenAPS communicated over the same protocol that CareLink uses, and requires no device be added on the pump
(tho you do want to make sure your basal type is set to "absolute" and not "percent" on the pump)
Dana Lewis
@danamlewis
Jul 07 2017 02:12 UTC
^ :+1:
PopcornPam
@PopcornPam_twitter
Jul 07 2017 02:25 UTC
Question for folks about max iob... I always end up with quite a few lows after I up my max iob, then after a few days autotuen catchest up and suggests a basal change that tends to fix it. Anyone else find that basals change iwth max iob? I only change it by .2-.4 at at time
Also, anyone online who uses the loop bridge for offline looping right now?
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 02:47 UTC
Thanks Dana and Cameron, hope you mean " Insulin Rate (U/H) or Percent of Basal" as "absolute or percent"?
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 02:56 UTC

so i waited for 30 min, lo look like this:
tail -F /var/log/openaps/pump-loop.log
Pumphistory less than 5m old
Settings less than 10m old
Pumphistory-24 less than 20m old
Completed pump-loop at Thu Jul 6 22:50:59 EDT 2017

Starting pump-loop at Thu Jul 6 22:51:03 EDT 2017:
Radio ok, Listening: .Starting pump-loop at Thu Jul 6 22:53:14 EDT 2017:
Radio ok, Listening: .No pump comms detected from other rigs
Old settings refreshError, retrying
Listening: .No pump comms detected from other rigs
mmtune: pump://JSON/mmtune/monitor/mmtune.json
reporting monitor/mmtune.json
"916.684", 5, -55 Starting pump-loop at Thu Jul 6 22:55:44 EDT 2017:
Radio ok, Listening: .

and attempt to check pump (openaps use pump model) still gives an error
File "/usr/local/lib/python2.7/dist-packages/serial/serialposix.py", line 528, in write
raise portNotOpenError
serial.serialutil.SerialException: Attempting to use a port that is not open
Cameron Chunn
@applehat
Jul 07 2017 03:03 UTC
Why are you trying to run ooenaps use pump model?
From the log you posted, it looks like the loop is working.
The command probably fails because the loop is using the port.
To talk to the pump
Running the old pump history command manually is probably what it'll take
Because that's what's erroring out in your logs you pasted
aliceinnowonderlands
@aliceinnowonderlands
Jul 07 2017 03:19 UTC
Ok, thanks for advices, i will try all this tomorrow
Cameron Chunn
@applehat
Jul 07 2017 03:21 UTC
Crap. Sorry, I totally missed the error in the logs.
I'm off my game today.
Dana Lewis
@danamlewis
Jul 07 2017 03:37 UTC
@applehat no worries. I have eagle eyes after 6-7 setups near me in last 24 hours. Also on my list to capture the log errors better for easier "which rabbit hole do I troubleshoot first" approach in the docs for first-timers
rsilvers129
@rsilvers129
Jul 07 2017 03:42 UTC
I am sort of stunned. I got in my replacement Explorer, and it is working 30 feet away from my pump. I have not tested the max range, but it is hugely better than the one I have been using, which had a 10 inch max range (literally, if it were in my left front pocket, and my pump were in my right front pocket, it wouldn’t have comms). This is a completely new and different OpenAPS experience for me. Now I can charge my rig on the nightstand next to my bed (it would be out of range with my other board).
Cameron Chunn
@applehat
Jul 07 2017 03:44 UTC
Welcome to normal rig operations!
Dana Lewis
@danamlewis
Jul 07 2017 03:44 UTC
That's more like it
Now you don't think we're crazy any more ;) I bet
At least on the rig range front :D
Cameron Chunn
@applehat
Jul 07 2017 03:48 UTC
I think we all have a tinge of crazy - we do let JavaScript control our blood glucose after all.
Dana Lewis
@danamlewis
Jul 07 2017 03:49 UTC
"Let"? By design ;)
Cameron Chunn
@applehat
Jul 07 2017 03:53 UTC
I personally love that it's Node. Easy to read and modify. I've just had fellow developers joke about it.
alternateal
@alternateal
Jul 07 2017 05:03 UTC
@Kdisimone - I managed to get Bluetooth working "automatically" by making the middle section of "oref0-bluetooth.sh" look like this (sorry on pad so posting code less easy) ///if ( hciconfig -a | grep -q "DOWN" ) ; then
sudo hciconfig hci0 up
sudo /usr/local/bin/bluetoothd --experimental &
sudo bt-pan client F0:DB:E2:CB:81:D1
sudo dhclient bnep0
fi
@Kdisimone - managed to get Bluetooth connecting "automatically" by making the middle section of oref0-Bluetooth.sh to look like this (sorry on pad so showing code less easy - I added two lines to the end - not it is my MAC address showing. if ( hciconfig -a | grep -q "DOWN" ) ; then
sudo hciconfig hci0 up
sudo /usr/local/bin/bluetoothd --experimental &
sudo bt-pan client F0:DB:E2:CB:81:D1
sudo dhclient bnep0
fi
katie disimone
@Kdisimone
Jul 07 2017 07:03 UTC
:+1: THANKS @alternateal
cameronrenwick
@cameronrenwick
Jul 07 2017 11:30 UTC
@rsilvers129 that is just awesome news!!! I've got my new explorer board swapped out as it will not communicate if it's further than 8 inches from my pump. It does talk to the pump, but I'll get a -85 at a hand's distance away. Sadly I've got 3 emails in to Hamshield from 4 days ago, none of which are replied to (all stating the same problem and directed to different people - 2 emails got ret'd). Is Morgan working there anymore?? Anyway, that's super exciting that you've got the range you do. I hope that they'll replace the one I have now. My other board gets about 10 feet or so, which I'm "ok" with but 20'd be awesome!
mkericson
@mkericson
Jul 07 2017 12:27 UTC
@tim2000s Thanks. Uptime Robot works perfectly
Marcus Lindfors
@Mackwe
Jul 07 2017 12:38 UTC
Hi.. Having problems again with OpenAPS not taking carbs into account. I got it working i oref0 (master) thanks to @danamlewis, using the info in http://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-2/troubleshoot-oref0-setup.html#users-712-users-x12-users (not step-by-step, but rebuilding one of the aliases). After this I upgraded to dev, with global-install and now that fix won't work. settings/carb_ratios.json is correct, but I can still not see any carbs taken into account. Can someone please let me know where the algo is (not) getting COB from?
ChrisWeinman
@ChrisWeinman
Jul 07 2017 13:21 UTC
We couldn't get openaps to pull carb info from the pump
I don't know if anyone else has had it working (this is with a 712).
Marcus Lindfors
@Mackwe
Jul 07 2017 13:29 UTC
@ChrisWeinman Read the link above. It does work on master. :-)
Sebastien Lussier
@SebastienLussier
Jul 07 2017 13:38 UTC
Hi Marcus, i have the same issue on dev with a 522, will investigate this weekend
I did not try with master
ChrisWeinman
@ChrisWeinman
Jul 07 2017 13:44 UTC
Sorry, I should have qualified that. We didn't get it working, but stopped trying after getting a 554!
Meghan Rutledge
@mar5477
Jul 07 2017 13:49 UTC
I could use some help fixing my rc.local. Yesterday I added the lines "hciconfig hci0 up; system start bluetooth.service; rfcomm bind hci0 MYPEBMAC" to rc.local by using nano. Everything continued to work fine (I assume because I didn't reboot) until my edison died and I plugged back in. Now it reboots after about 45 seconds and turns off after rebooting 3 times. When booting I get 2 failed statuses, one for "Failed to start Load Kernel Modules" and one for "Failed to start /etc/rc.local Compatibility" When I look into systemctl status re-evaluation.service it mentions that it can't get the device info (I assume my pebble MAC), so I tried to delete the lines from rc.local that I added yesterday and have been able to save and had "[]
... had "[Wrote 36 lines]" returned. Then it rebooted and the lines were back.
Meghan Rutledge
@mar5477
Jul 07 2017 14:16 UTC
Update! Kept trying to get in and delete the 3 lines and save it within 45 seconds of getting to the login menu after booting and something finally stuck. That fixed my failed rc.local issues and even though pancreabble still isn't working, at least I'm back looping.
cameronrenwick
@cameronrenwick
Jul 07 2017 14:56 UTC
still working thru getting my head around writing recipes for IFTTT. If I wanted to make several buttons for "eating" would I just take this recipe {"enteredBy": "IFTTT-button", "reason": "low treatment", "carbs": 10, "secret": "your_hashed_api_goes_here!!!"} and alter the low treatment to eating and the carb value to whatever amount I want?
Meghan Rutledge
@mar5477
Jul 07 2017 15:03 UTC
Pretty much! Just make sure you use the hashed API, not the plain text one.
Marcus Lindfors
@Mackwe
Jul 07 2017 15:08 UTC
@ChrisWeinman We have a 754 (which is the same as 554) and everything worked on master except for the carb_ratio. The link I sent helped me fix this though. So maybe I need to go back to master then... :-/
@SebastienLussier Looking forward to your results. Seems we need to go back to master for now. Not a huge problem but please keep me posted (PM preferably). Thanks!
cameronrenwick
@cameronrenwick
Jul 07 2017 15:13 UTC
thanks @mar5477 ..yes, the toughest part of making IFTTT buttons is getting the hashed API...
tepidjuice
@tepidjuice
Jul 07 2017 15:27 UTC
how do I set temptargets as per https://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-1/offline-looping-and-monitoring.html#temporary-targets with the latest version of dev? If I get rid of openaps ns-temptargets from ns-loop I get: BG data is too old (it's probably this), or clock set incorrectly. The last BG data was read at Sat Jul 08 2017 01:00:54 GMT+1000 (AEST) but your system time currently is Sat Jul 08 2017 01:19:33 GMT+1000 (AEST) "reason": "BG data is too old (it's probably this), or clock set incorrectly. The last BG data was read at Sat Jul 08 2017 01:00:54 GMT+1000 (AEST) but your system time currently is Sat Jul 08 2017 01:19:33 GMT+1000 (AEST)" Checking system clock against pump clock: Checking deliverAt: null is within 1m of current time: Sat Jul 8 01:19:34 AEST 2017 date: invalid date ‘null’
Scott Leibrand
@scottleibrand
Jul 07 2017 15:37 UTC
What did you do to "get rid" of it?
tepidjuice
@tepidjuice
Jul 07 2017 15:42 UTC
vim openaps.ini -> /ns-temptargets -> d3w -> :wq
Meghan Rutledge
@mar5477
Jul 07 2017 15:45 UTC
@cameronrenwick were you able to find that?
Scott Leibrand
@scottleibrand
Jul 07 2017 15:47 UTC
@tepidjuice that would break everything on my openaps.ini. Can you give me something approximating a diff?
Or just the "what does it look like after your change"
tepidjuice
@tepidjuice
Jul 07 2017 15:48 UTC
On line 325 it reads ... &&openaps get-ns-bg; && echo -n..
Sorry can't do a diff I'm on my phone
Scott Leibrand
@scottleibrand
Jul 07 2017 15:49 UTC
Me too. :smile:
tepidjuice
@tepidjuice
Jul 07 2017 15:50 UTC
So only openaps ns-temptargets is gone
Gitter on a phone is pretty bad.
I comiserate
Scott Leibrand
@scottleibrand
Jul 07 2017 15:50 UTC
Did you delete the alias definition? Or the call of it from another alias, or ?
tepidjuice
@tepidjuice
Jul 07 2017 15:51 UTC
I removed it from ns-loop defined on line 325 of openaps.ini
the rest of ns-loop is still there.
Scott Leibrand
@scottleibrand
Jul 07 2017 15:52 UTC
Mine looks like ns-loop = ! bash -c "echo Starting ns-loop at $(date): && openaps get-ns-bg; openaps ns-temptargets && echo -n Refreshed temptargets && openaps ns-meal-carbs && echo " and meal-carbs" && openaps battery-status; cat monitor/edison-battery.json; echo; openaps upload"
So you just removed openaps ns-temptargets && from there? Or ?
tepidjuice
@tepidjuice
Jul 07 2017 15:54 UTC
ns-loop = ! bash -c "echo Starting ns-loop at $(date): && openaps get-ns-bg; && echo -n Refreshed temptargets && openaps ns-meal-carbs && echo " and meal-carbs" && openaps battery-status; cat monitor/edison-battery.json; echo; openaps upload"
Scott Leibrand
@scottleibrand
Jul 07 2017 15:54 UTC
I don't see how that could affect its ability to get-ns-bg, unless you introduced a syntax error.
Oh, you did
; && is invalid
Do one or the other
tepidjuice
@tepidjuice
Jul 07 2017 15:55 UTC
Of course smacks forehead
Thanks
Scott Leibrand
@scottleibrand
Jul 07 2017 15:56 UTC
I've done that many times. :smile:
cameronrenwick
@cameronrenwick
Jul 07 2017 16:42 UTC
@mar5477 I think you're referring to finding the hashed api and yes, I've got it thanks. I've got several IFTTT buttons, just none that are for carbs eaten.. Now that I'm SMBing I'd like to make 3 or 4 that represent 10, 15, 20, 25 gm carbs... just trying to get the SMB entry process streamlined
fjungman
@fjungman
Jul 07 2017 16:49 UTC
I'm trying to tune the settings, but one thing I don't understand, and it is the last thing I need to fix, is why does oref0 predict the BG will rise in the long term, even with no carbs on board? It always does this, so he usually wakes up low, or more often, I go in and give him carbs to make it through to morning (afternoon, since he is a teen on summer vacation). What factors would make the system think the BG will rise on its own?
Screenshot_20170707-070931.png
fjungman
@fjungman
Jul 07 2017 17:02 UTC
I guess you can see this in the spikes on the lower graph. Giving carbs with no bolus...
Scott Leibrand
@scottleibrand
Jul 07 2017 17:30 UTC
That's because IOB is -1.31, so it expects BG to rise 1.31 * ISF (+/- any deviation extrapolations etc.)
You might need to time-shift his lower overnight basals later into the morning if he's sleeping in later. Autotune is probably suggesting that, but may not be caught up, or may be limited by your min/max safety factors.
When basal is too high, it has to zero temp to compensate, and doing so results in lots of negative IOB, which it takes to mean BG will rise later. If that's happening because of an overall 24x7 increase in sensitivity, then autosens will adjust for it. but if it's only happening at certain times of day due to mis-timed basal from adjusted sleep schedules, those basals need to be adjusted.
fjungman
@fjungman
Jul 07 2017 17:43 UTC
Thank you, that makes sense now! I never considered that the negative IoB was used. I thought of it more like negative cows...
Scott Leibrand
@scottleibrand
Jul 07 2017 17:44 UTC
hah, no, net IOB is relative to "neutral basal", so it can be negative just as easily as positive
fjungman
@fjungman
Jul 07 2017 17:48 UTC
"CLICK". I got it now. This should be easy to fix.
Scott Leibrand
@scottleibrand
Jul 07 2017 17:50 UTC
Since this was non-obvious to you, I'm sure it will trip up others too, so if you could PR in any clarifications to the docs that would've helped make it click sooner, that would be very useful.
DaisyHK
@laurathiessen
Jul 07 2017 17:53 UTC
if I dont have the short cuts set up in OpenAPS what command do i use to add a wifi network? vi /etc/network/interfaces brings up a warning that the file is laready in use?
image.png
fjungman
@fjungman
Jul 07 2017 17:53 UTC
@scottleibrand will do!
Scott Leibrand
@scottleibrand
Jul 07 2017 17:55 UTC
@laurathiessen that's like the Word "autorecovery" thing, indicating that the last time you edited the file you didn't save and quit before the computer shut down. you can recover the file if you had edits you care about, or just delete the autorecovered version
that'd be another good thing to PR in a clarification for.
DaisyHK
@laurathiessen
Jul 07 2017 17:58 UTC
oh ok... so if i want to keep the files entered its E edit anyways. or should I use a different command? Also to save it "Press Esc and then type ‘:wq’ and press Enter to write the file and quit"
Scott Leibrand
@scottleibrand
Jul 07 2017 18:04 UTC
If you do E to edit anyways, it'll keep asking you every time. If you hit D to delete the autosaved version, it'll shut up about it.
Tim Street
@tim2000s
Jul 07 2017 19:15 UTC
@LilDucky You can buy the Minimed transmitters direct from Medtronic. They still sell them.
Right then. My edison board that won't flash Jubilinux won't flash Ubilinux either. All it will flash is Yocto, so I guess we're in a dead situation.
Tim Street
@tim2000s
Jul 07 2017 19:22 UTC
I'll swap the EXB just to be sure but that doesn't look good
@tim2000s I wrote this a while ago: with some work, you can upgrade to jubilinux "by hand" without flashing: https://gist.github.com/ecc1/015689ab68baf30832fbe125b7cbc693
Scott Leibrand
@scottleibrand
Jul 07 2017 19:41 UTC
@tim2000s it won't flash (j)ubilinux even after flashing yocto?
Tim Street
@tim2000s
Jul 07 2017 20:18 UTC
no
Just refuses to accept it.
Been back to Yocto twice
On a different note - testing the new setup script.
I didn't see an option for oref1?
Dana Lewis
@danamlewis
Jul 07 2017 20:25 UTC
@tim2000s in advanced features menu
Oh
Not with wifi script
It installs master
So won't see all the dev related stuff w that until release to master happens
Tim Street
@tim2000s
Jul 07 2017 20:25 UTC
Ah
okay
Scott Leibrand
@scottleibrand
Jul 07 2017 20:26 UTC
but easy enough to cancel it when oref0-setup starts and get dev manually
Dana Lewis
@danamlewis
Jul 07 2017 20:26 UTC
:+1:
Tim Street
@tim2000s
Jul 07 2017 20:26 UTC
no worries
Oooh
There's a bug.
When you say "n" to interactive set up it goes ahead and starts it anyway, using n as your opens directory
Dana Lewis
@danamlewis
Jul 07 2017 20:28 UTC
Heh surprised no one caught that on master ever, but maybe not since anyone running oref0 setup does want it ;)
Probably exists on dev too if you want to target your Pr then and get it fixed.
You can ctrl-c out of script though for now
Scott Leibrand
@scottleibrand
Jul 07 2017 20:30 UTC
Is that because you hit enter at some point before oref0-setup started?
we probably just need to read and clear stdin before asking any real questions
DaisyHK
@laurathiessen
Jul 07 2017 20:48 UTC
@scottleibrand but if i but D will it delete the last inputs i added? I want to edit the file that was not saved then only save that file
Scott Leibrand
@scottleibrand
Jul 07 2017 20:58 UTC
if you want to keep the unsaved edits, that would mean recovering the autosaved version. if you don't want to keep the unsaved edits (or there aren't any) then you can delete it.
Tim Street
@tim2000s
Jul 07 2017 20:59 UTC
I must be being blind here. I can only see one pass phrase for the advanced featrues
Okay - 15 mins of re-searching the page is quite annoying! Found it though.
Scott Leibrand
@scottleibrand
Jul 07 2017 21:05 UTC
@tim2000s this should help with any extra enters sitting on stdin, and also give you a chance to stop the bootstrap before running oref0-setup from master: openaps/docs@c02eadf
(if you cancel at that point and want to do dev, you can just git checkout dev, do npm run global-install, and then run oref0-setup)
Tim Street
@tim2000s
Jul 07 2017 21:08 UTC
Thanks Scott - I'd dumped out and checked Dev out already :smile:
Scott Leibrand
@scottleibrand
Jul 07 2017 21:10 UTC
Yeah, I figured. Just thought I'd make it obvious when that should be done if that's your goal.
Tom Petrillo
@tompetrillo
Jul 07 2017 21:12 UTC
@danamlewis Dana, I think I saw on here that you are using the Dana*R pump (ironic). How easily are you able to get supplies for it? Are you able to get them covered by US insurance? I have relatives visiting from out of country and see a used pump on craigslist equivalent, not sure on how much other costs will be though (or feasibility).
Dana Lewis
@danamlewis
Jul 07 2017 21:13 UTC
I’m not using the DANA*R pump
Tom Petrillo
@tompetrillo
Jul 07 2017 21:14 UTC
then it was just a name similarity confusion.
Scott Leibrand
@scottleibrand
Jul 07 2017 21:36 UTC
I can't speak to ease or insurance, but I do know that the DANA Diabecare IIS pump is FDA approved in the US, and that SOOIL sells supplies for it here. Those same supplies are what you'd need if you have a DANA*R pump.
Tom Petrillo
@tompetrillo
Jul 07 2017 21:37 UTC
Thanks Scott.
Tim Street
@tim2000s
Jul 07 2017 21:39 UTC
The Dev set-up worked with no issues. Very pleased.
Also seem to have overcome my issues with the wifi wpa_supplicant on Jubilinux.
I think using a USB hub from the USB-C port screws up comms a bit to the Edison
Scott Leibrand
@scottleibrand
Jul 07 2017 21:48 UTC
yeah, we've heard other people complain about that
Dana Lewis
@danamlewis
Jul 07 2017 21:49 UTC
@tim2000s :+1:
Tim Street
@tim2000s
Jul 07 2017 22:09 UTC
PRd a note into the docs about that
Dana Lewis
@danamlewis
Jul 07 2017 22:09 UTC
thx
DaisyHK
@laurathiessen
Jul 07 2017 22:28 UTC
k thanks @scottleibrand
image.png
DaisyHK
@laurathiessen
Jul 07 2017 22:33 UTC
sorry @scottleibrand but this comes up when i pushed recovery... not sure how to input any commands or what to do
Scott Leibrand
@scottleibrand
Jul 07 2017 22:37 UTC
You're still in vi (the editor, like Word). You have to get the file the way you want and then do Esc :wq to save and quit, or Esc :q! to quit without saving.
DaisyHK
@laurathiessen
Jul 07 2017 22:43 UTC
ok think i gt if figured out... also inputted a few command lines of just "network={
ssid="my network"
psk="my wifi password"
}
so that i can enter more later easily thanks hopefuly this works
dougtakeuti
@dougtakeuti
Jul 07 2017 22:49 UTC
We were offline for a week (MDT 722 + Enlite + OpenAPS) and just restarted looping. Glucose data is uploading fine to NS and the rig is setting temp basals ok. However, we have two issues: 1) pumphistory.json is not current so that is shows data from July 2, when we went offline. The bolus from one hour ago does not show, so that iob is incorrect. The monitor folder is being updated periodically. The issue seems to be that the pump is not delivering history data. 2) A minor issue is that temp basals are not showing on NS. There are no future events and I have tried openaps first-upload a couple of times. Any hints would be welcome.
Dana Lewis
@danamlewis
Jul 07 2017 22:58 UTC
@markt1d you’ll need to get your rig parts, and you’ll follow the setup same as anyone else, and tell it “xdrip” as the BG source. after that, you’ll follow the xdripAPS instructions: http://openaps.readthedocs.io/en/latest/docs/walkthrough/phase-1/offline-looping-and-monitoring.html#xdripaps-for-offline-bgs-for-android-users for getting the BGs locally to your rig
I’d still recommending telling OpenAPS about your NS so you can use it to visualize things when you ARE online (and it’s great for initial troubleshooting), but otherwise the xdrip route should work well for you.
and - @AdrianLxM who had also responded in the other channel - will be a good resource in case there’s any issues with the Libre->xdrip+ piece of the puzzle, since there’s not as many folks running Libre (yet).
franckvalli
@franckvalli
Jul 07 2017 23:09 UTC
@danamlewis Hi
Dana Lewis
@danamlewis
Jul 07 2017 23:10 UTC
@franckvalli hi! Ok. So your mmtune results might be related to the WW pump. Tagging @PieterGit since he’s most familiar with the WW radio stuff and may have some ideas for troubleshooting and/or may have a particular branch to suggest that you run if there’s a fix already in place
Mark
@markt1d
Jul 07 2017 23:10 UTC
thanks @danamlewis and @AdrianLxM some reading to do!
franckvalli
@franckvalli
Jul 07 2017 23:13 UTC
@danamlewis I put WW as there is neither NA nor WW in my pump numbers and because it was purchased in France (but made in California...). I may try re-run with NA instead? @PieterGit
Dana Lewis
@danamlewis
Jul 07 2017 23:13 UTC
ohhh
yea
run it as NA then
franckvalli
@franckvalli
Jul 07 2017 23:14 UTC
@danamlewis I will try and let you know. Thanks again @PieterGit