These are chat archives for nightscout/intend-to-bolus

19th
Oct 2017
garykidd
@garykidd
Oct 19 2017 00:44 UTC
the two antenna connectors on the explorer board are for what?
Steve Bernacki
@sbernacki
Oct 19 2017 00:45 UTC
image.png
Hi there - so we upgraded to the dev last night, and I realized this evening that the rig battery is no longer displaying on NightScout (see above)
garykidd
@garykidd
Oct 19 2017 00:45 UTC
one on top? one on bottom?
Steve Bernacki
@sbernacki
Oct 19 2017 00:46 UTC
See it in the pump-loop.log logs, however:
 Edison on battery: 45%.
garykidd
@garykidd
Oct 19 2017 00:47 UTC
that sometimes takes a bit to show up @sbernacki ...been awhile?
I see this one.....
Steve Bernacki
@sbernacki
Oct 19 2017 00:51 UTC
Checked a screenshot that my wife made yesterday morning (before the OpenAPS update to dev) and the battery indicator was definitely there.
image.png
Scott Leibrand
@scottleibrand
Oct 19 2017 00:52 UTC
@garykidd AFAIK there's only one antenna connector on the Explorer block itself, for the 900MHz cc1110 antenna. Are you talking about the other one on the Edison? If so, that's for the 2.4GHz wifi/bluetooth chip.
garykidd
@garykidd
Oct 19 2017 00:52 UTC
blob
not this one^
right---meant edison..thx
but there is an antenna connector onthe chip.
garykidd
@garykidd
Oct 19 2017 01:00 UTC
here it is...looks like external wifi antenna....interestingly...mine is already missing the resistor to force connection to internal connector....mayhave to add a wire to this connector if wifi performance is off---i'm 100% sure I didnt remove the resistor though---maybe this was pre-wired as an external antenna configuration from factory...
garykidd
@garykidd
Oct 19 2017 01:14 UTC
OK, flashing rig #4....thinking...this is fun...and so easy now.
@sbernacki have you updated NS version lately?
cameronrenwick
@cameronrenwick
Oct 19 2017 01:20 UTC
so, if I read that link right... it says DON'T use the antennae connection on the edison board... it's a test point that intel uses when they build the edison. OTOH, using an antennae on the EB is fine (if you so choose) and, in my case took my mmtune from -80ish to -60ish... worth it IMO
garykidd
@garykidd
Oct 19 2017 01:22 UTC
@cameronrenwick it's actually a different connector
cameronrenwick
@cameronrenwick
Oct 19 2017 01:23 UTC
oh good... no worries then!
garykidd
@garykidd
Oct 19 2017 01:23 UTC
but it does indicate like you said--but I think it may have been an oversimplification
Steve Bernacki
@sbernacki
Oct 19 2017 01:23 UTC
@garykidd upgraded NS on Sunday night, but after the upgrade the battery pill was working; seems like it disappeared after the openaps 0.5.5-dev upgrade last night
garykidd
@garykidd
Oct 19 2017 01:24 UTC
some others commented below about how adding an antenna helped---Ihtink you just need to remove that small ....stupid small inline resistor---which mine doesnt have any way...
loving smaller SMB visualization...
Dana Lewis
@danamlewis
Oct 19 2017 01:25 UTC
@sbernacki master is 0.5.5. Dev would be 0.6.0. Which are you on?
garykidd
@garykidd
Oct 19 2017 01:25 UTC
blob
now if @scottleibrand will pointme in the direction of where basal rendering can be updated (as easily)...would like to tweak that as well....
Steve Bernacki
@sbernacki
Oct 19 2017 01:27 UTC
oops
root@edison1:/var/log/openaps#  npm list -g oref0
/usr/local/lib
└── oref0@0.6.0-dev1  -> /root/src/oref0
Scott Leibrand
@scottleibrand
Oct 19 2017 01:27 UTC
the only reason I've made progress on anything with NS is many hours of beating my head against the wall randomly changing things to see what it does
so if I haven't directly touched it, don't expect me to have any insight into how to change something in NS. @sulkaharo might be helpful though
garykidd
@garykidd
Oct 19 2017 01:28 UTC
OK...cool... I'm just not sure how soomeof the arguments are passed
Scott Leibrand
@scottleibrand
Oct 19 2017 01:28 UTC
tell me about it. whomever wrote NS does much more advanced JS than I do (which isn't necessarily saying much)
garykidd
@garykidd
Oct 19 2017 01:28 UTC
@scottleibrand sorry in our eyes you can do anything now...
cameronrenwick
@cameronrenwick
Oct 19 2017 01:29 UTC
kinda reminds me of the last triathlon I was in @scottleibrand ... feels soo good when you stop :smile:
Steve Bernacki
@sbernacki
Oct 19 2017 01:29 UTC
Updated last night, last commit was
commit 197f44fd4ed975dcc9290aae7536dd8b1eaa6d79
Author: Scott Leibrand <scottleibrand@gmail.com>
Date:   Tue Oct 17 15:37:31 2017 -0700
garykidd
@garykidd
Oct 19 2017 01:29 UTC
@cameronrenwick nice work w/the tri's
Scott Leibrand
@scottleibrand
Oct 19 2017 01:29 UTC
@sbernacki there's probably some edison-voltage stuff in ns-loop that I didn't port over to oref0-ns-loop.sh
yep, I missed lib/oref0-setup/edisonbattery.json
garykidd
@garykidd
Oct 19 2017 01:33 UTC
C probably isntbeing used that much these days.....C++ still kicking?
Scott Leibrand
@scottleibrand
Oct 19 2017 01:39 UTC
I assume C is just considered a subset of C++ nowadays. they're still the best language for compiling efficient code
garykidd
@garykidd
Oct 19 2017 01:41 UTC
wonder if it might be an avenue to optimize pi0w
Scott Leibrand
@scottleibrand
Oct 19 2017 01:42 UTC
nope
If I have to learn another language and compile code, it will slow me way down
garykidd
@garykidd
Oct 19 2017 01:47 UTC
so is the main language that you're coding in python?
@garykidd The entire Linux kernel is written in C.
garykidd
@garykidd
Oct 19 2017 01:48 UTC
unix and linux too...no?
meant that the other way around linix and unix too, right?
Scott Leibrand
@scottleibrand
Oct 19 2017 01:50 UTC
@sbernacki openaps/oref0#731 is now ready for you to test
Yes, C was invented for Unix.
Steve Bernacki
@sbernacki
Oct 19 2017 01:53 UTC
@scottleibrand Amazing! Pulling it down now and will report back, thank you!
Scott Leibrand
@scottleibrand
Oct 19 2017 01:54 UTC
@garykidd no, I code in javascript and bash. the underlying openaps stuff that Ben did is all python, but I touch that as little as possible
garykidd
@garykidd
Oct 19 2017 01:54 UTC
gotchya
and JS and bash can both be command line interpreted?
There are other systems programming languages these days that compile to efficient code but are "higher level" than C (stronger type systems, more automatic memory management): Rust, Swift, and Go are probably the leading contenders
Scott Leibrand
@scottleibrand
Oct 19 2017 01:58 UTC
some of those have the same problem as java with the garbage collection performance hit (which is usually worthwhile to not have to do C-style low-level memory management, but can hurt you for high-performance applications)
(I've never coded in any of them, just have 2nd-hand knowledge of the problems complained about by people who do)
PopcornPam
@PopcornPam_twitter
Oct 19 2017 02:01 UTC
@KS615 , iphone 8, but always iphone
garykidd
@garykidd
Oct 19 2017 02:12 UTC
@scottleibrand was thinking about autotune recommendations a bit while driving home.... was thinking that you may not want to make any adjustments unless they are significant enough...is that how the recommendations are derived? While they definitely need ot be capped as they are--was wondering if a "cushion" before any recommendations are recommended is appropriate...then I thought..maybe it works that way already...
Scott Leibrand
@scottleibrand
Oct 19 2017 02:16 UTC
@garykidd autotune is designed to run quietly in the background, so that you don't have to worry about it. so it makes tiny adjustments whenever it has data to indicate it should. we don't expect the human to look for recommendations very often.
it might be useful to highlight which changes are big enough to be worth worrying about (particularly those hitting the safety caps) if anyone wants a UX project
the autotune UX could use a lot of improvement in many ways. pretty much the only thing that works as I'd like is the automatic on-rig adjustments
Craig Brenner
@cbrenner
Oct 19 2017 02:38 UTC

Saw this announcement today from JDRF..."New Initiative to Pave Way for Open Protocol Automated Insulin Delivery Systems" Hope this will have some impact and sooner rather than later...

http://www.jdrf.org/press-releases/jdrf-announces-new-initiative-to-pave-way-for-open-protocol-automated-insulin-delivery-systems/ .... just noticed Dana posted this earlier...

Steve Bernacki
@sbernacki
Oct 19 2017 02:41 UTC
@scottleibrand commented on the PR but battery status is back in nightscout. Thank you!
Dana Lewis
@danamlewis
Oct 19 2017 02:44 UTC
@sbernacki :+1:
garykidd
@garykidd
Oct 19 2017 02:49 UTC
@scottleibrand I like the idea of highlighting those recommendations that exceed safety caps.....thinking..you dont want to be adjusting basals on pump too often...but you should if they are sufficiently deviated from what they should be. thx
garykidd
@garykidd
Oct 19 2017 03:00 UTC
OK, so latest rig has access to wifi...but no internet...reboot router?
sysyc
@sysyc
Oct 19 2017 03:37 UTC
微信图片_20171019113352_副本.jpg
I want install bluetooth tethering on oref0-setup,but had error above and what can I do?
Scott Leibrand
@scottleibrand
Oct 19 2017 03:49 UTC
Try again?
Maybe on a better Internet connection
Scott Leibrand
@scottleibrand
Oct 19 2017 04:46 UTC
For anyone with tiny basals who hasn't been able to use SMB, but is interested in doing so, I'd like your thoughts on openaps/oref0#732 - that needs some discussion before I'd be comfortable merging it, particularly from those who'd be most affected.
Nalla306
@Nalla306
Oct 19 2017 07:36 UTC
@mmadeva
I had that issue, was due to me entering a blood glucose value into the bolus wizard
sysyc
@sysyc
Oct 19 2017 08:18 UTC
I've tried several times, and in different Internet connection,stops here every time @scottleibrand
Velibor Maric
@vebaba
Oct 19 2017 08:45 UTC
Hi all. I have a problem. Rig stopped to respond. It might be due to battery power supply problem. Need to test. Anyway, the rig was offline for an hour and now in pump log I can see this error:
```
RefreshValueError: need more than 0 values to unpack
Its connected to Old pumphistory
Velibor Maric
@vebaba
Oct 19 2017 09:01 UTC
OK @scottleibrand I'm drilling, you're right, I should try to learn...
Velibor Maric
@vebaba
Oct 19 2017 09:11 UTC
I stopped the cron, killed openaps instances, ran pump-loop, confirmed refresh old pumphistory error, killed openaps processes, ranopenaps refresh-old-pumphistory and it done it w/o errors. After that, everything works again. I'm puzzled how isolated process run healed itself @scottleibrand
Mike
@libxmike
Oct 19 2017 09:41 UTC
@sbernacki don't hold you breath, this will not happen soon, if at all, give it maybe 10 years.
James
@in-10-city
Oct 19 2017 13:51 UTC
I would love some help with setting up my NTP server
Waiting for ntpd to synchronize... No!
ntpd did not synchronize.
Restarting ntp (via systemctl): ntp.service.
Waiting for ntpd to synchronize... No!
ntpd did not synchronize.
I edited /etc/systemd/timesyncd.conf
and modified #Servers=0.debian.pool.ntp.org 1.debian.pool.ntp.org 2.debian.pool.ntp.org 3.debian.pool.ntp.org
to look like this
Servers=0.128.138.140.44 1.debian.pool.ntp.org 2.debian.pool.ntp.org 3.debian.pool.ntp.org
James
@in-10-city
Oct 19 2017 13:56 UTC
exited vi with saving and rebooted
but still getting that error listed above
@in-10-city You might understandably think the 0. 1. 2. etc in the servers list are part of some configuration scheme, but they're not: they're actually part of the server hostnames (try "nslookup 2.debian.pool.ntp.org"). So your first one shouldn't have a leading "0.".
James
@in-10-city
Oct 19 2017 14:08 UTC
thanks @ecc1 I will do that when I get back to my desk
never fails when you get something good to work off of... you get pulled away to do that work stuff...
Samuchco
@Samuchco
Oct 19 2017 14:49 UTC
BG 155, bolused 7 units at 9:04 for 30 gr went up to 260. No SMB here is the recent papertrail, will post screen shot after.

Oct 19 10:43:45 SammysAPS pump-loop.log: Autotune exists! Hoorah! You can use microbolus-related features.
Oct 19 10:43:45 SammysAPS pump-loop.log: {"carbs":30,"mealCOB":0,"currentDeviation":1.87,"maxDeviation":3.89,"minDeviation":1.57,"slopeFromMaxDeviation":-0.5,"slopeFromMinDeviation":0.043,"allDeviations":[2,3,3,4,3,2,2,2],"lastCarbTime":1508418267000}
Oct 19 10:43:45 SammysAPS pump-loop.log: {"iob":3.956,"activity":0.0354,"basaliob":-1.053,"bolusiob":5.009,"netbasalinsulin":-1.55,"bolusinsulin":7,"time":"2017-10-19T14:43:38.000Z","iobWithZeroTemp":{"iob":3.956,"activity":0.0354,"basaliob":-1.053,"bolusiob":5.009,"netbasalinsulin":-1.55,"bolusinsulin":7,"time":"2017-10-19T14:43:38.000Z"},"lastBolusTime":1508418267000,"lastTemp":{"rate":1.85,"timestamp":"2017-10-19T10:32:37-04:00","started_at":"2017-10-19T14:32:37.000Z","date":1508423557000,"duration":12.06}}
Oct 19 10:43:45 SammysAPS pump-loop.log: {"delta":-5,"glucose":215,"short_avgdelta":-3.61,"long_avgdelta":-1.32}
Oct 19 10:43:45 SammysAPS pump-loop.log: Autosens ratio: 0.72; Adjusting basal from 1.75 to 1.25; ISF from 25 to 34.7
Oct 19 10:43:45 SammysAPS pump-loop.log: currenttemp: { duration: 20, rate: 1.85, temp: 'absolute' } lastTempAge: 11 m tempModulus: 1 m
Oct 19 10:43:45 SammysAPS pump-loop.log: Last carbs 99 minutes ago; remainingCATime: 5.5 hours; 100% carbs absorbed
Oct 19 10:43:45 SammysAPS pump-loop.log: Carb Impact: 1.1 mg/dL per 5m; CI Duration: 0 hours; remaining CI (~2h peak): 0 mg/dL per 5m
Oct 19 10:43:45 SammysAPS pump-loop.log: UAM Impact: 1.1 mg/dL per 5m; UAM Duration: 0.3 hours
Oct 19 10:43:45 SammysAPS pump-loop.log: minPredBG: 96 minIOBPredBG: 71 minZTGuardBG: 96 avgPredBG: 96 COB: 0 / 30
Oct 19 10:43:45 SammysAPS pump-loop.log: BG projected to remain above 80 for 145 minutes
Oct 19 10:43:45 SammysAPS pump-loop.log: naive_eventualBG: 78 bgUndershoot: -18 zeroTempDuration: 240 zeroTempEffect: 242 carbsReq: -62

Oct 19 10:43:45 SammysAPS pump-loop.log: Checking deliverAt: 2017-10-19T14:43:45.583Z is within 1m of current time: Thu Oct 19 10:43:45 EDT 2017
Oct 19 10:43:45 SammysAPS pump-loop.log: and that smb-suggested.json is less than 1m old
Oct 19 10:43:45 SammysAPS pump-loop.log: enact/smb-suggested.json: {"insulinReq":0.03,"bg":215,"reservoir":"241.6","temp":"absolute","predBGs":{"ZT":[215,209,202,196,189,181,174,167,160,153,147,141,135,130,125,121,117,113,110,107,104,102,100,98,97,96,96,96,96,96],"IOB":[215,210,204,198,192,185,178,172,165,158,152,146,140,134,129,124,119,114,110,106,102,99,96,93,90,87,85,83,81,79,77,76,75,74,73,72,72,71,71,71,72,72,73,73,74,74,74,75]},"rate":1.3,"IOB":3.956,"reason":"COB: 0, Dev: 7, BGI: -6.14, ISF: 35, Target: 80, minPredBG 96, minGuardBG 71, IOBpredBG 75; Eventual BG 85 >= 80, 20m@1.85 > 2 * insulinReq. Setting temp basal of 1.3U/hr. ","COB":0,"eventualBG":85,"duration":30,"tick":-5,"deliverAt":"2017-10-19T14:43:45.583Z"}
Oct 19 10:43:50 SammysAPS pump-loop.log: Temp refreshed: monitor/temp_basal.json: {"duration":20,"rate":1.85,"temp":"absolute"}
Oct 19 10:43:53 SammysAPS pump-loop.log: enact/smb-enacted.json: "Rate: 1.3 Duration: 30"
Oct 19 10:43:56 SammysAPS pump-loop.log: Temp refreshed: monitor/temp_basal.json: {"duration":30,"rate":1.3,"temp":"absolute"}
Oct 19 10:43:56 SammysAPS pump-loop.log: No bolus needed (yet). Settings less than 15 minutes old. Edison on battery: 78%. Pumphistory-24 < 30m old
Oct 19 10:44:30 SammysAPS pump-loop.log: Settings refreshed. Refreshed pumphistory and meal.json
Oct 19 10:44:37 SammysAPS pump-loop.log: IOB: 3.931
Oct 19 10:44:37 SammysAPS pump-loop.log: Completed supermicrobolus pump-loop at Thu Oct 19 10:44:37 EDT 2017

Screenshot (10).png
katie disimone
@Kdisimone
Oct 19 2017 15:09 UTC

@Samuchco looks like you may not have needed smbs and therefore did not get them. You were suspended for half the time of the screenshot and the prediction looks like you may be near target in future.

But, wouldn’t hurt to double check if you have your smbs turned on in preferences cat-pref

garykidd
@garykidd
Oct 19 2017 15:10 UTC
does anyone know IP address range of android via BT tethering....having a terribly hard time ssh'ing into rig....
Samuchco
@Samuchco
Oct 19 2017 15:14 UTC
@Kdisimone thanks. What does "You were suspended for half the time......" . Does suspended mean zero temp? Also, I temp target 80/80 but no smb either. I did do a reinstall yesterday, but I checked the pref and I believe smb was true. I will check his rig when he is home this evening.
Velibor Maric
@vebaba
Oct 19 2017 15:15 UTC
@garykidd 192.168.44.42 with me as 1st device connected
if Rig is connected, BT sign will get additional two triangles on the sides. Like here: https://lh4.ggpht.com/S9D1z_mhuFUao6VRVdVwV6xeAU2kTtYgQHhg7O00JDiT6AJnlmVUV9kERRDgROkC3A=w300
garykidd
@garykidd
Oct 19 2017 15:34 UTC
which app our you using to identify IP?
Samuchco
@Samuchco
Oct 19 2017 15:40 UTC
@Kdisimone can I check if smb is enabled via papertrail? if so how?
garykidd
@garykidd
Oct 19 2017 15:40 UTC
I've got two rigs connected via BT....1 has internet access...one does not.
Velibor Maric
@vebaba
Oct 19 2017 15:51 UTC
@garykidd I connected via UART (serial) on Explorer, found IP there and made Putty and Termius connections later. It was always the same IP.
My 522 pump just completely died. I had a lithium AAA battery in it which was showing as dead on the LCD (must have missed the low battery alarm), and when I replaced the battery the LCD didn't come back on at all. No error messages, nothing. Tried several batteries. Anyone seen this failure mode before?
cameronrenwick
@cameronrenwick
Oct 19 2017 16:13 UTC
have you tried a different battery cap Eric? I had one go bad and the pump behaved as yours did... new (or cleaned for good connection of +/- on battery) was my savior... good luck, these pumps are worth their weight in gold...
It seems to have recovered on its own after being without a battery for 30 minutes. Whew!
But thanks for that suggestion, will file it away
Mike
@libxmike
Oct 19 2017 16:23 UTC
@ecc1 I have a different battery problem, don't know if this is normal, after almost every battery replace I have to prime and reset the clock
Do you get the "out of battery limit" error? Maybe whatever they use to store energy when the battery is out (capacitor or smaller cell?) has failed?
garykidd
@garykidd
Oct 19 2017 16:26 UTC
finally was able to find darn IP addresses when connected via mobile BT hotspot....
i couldn't get the other apps listed in the docs to work...
Mike
@libxmike
Oct 19 2017 16:29 UTC
@ecc1 yes I get out of battery limit error, sometimes shows even 1.2V , I guess the cap is old and cant old to backup EPROM (if there is one) . I think once with 1.35V didn't need to rewind prime
garykidd
@garykidd
Oct 19 2017 16:45 UTC
Starting supermicrobolus pump-loop at Thu Oct 19 
12:16:02 EDT 2017 with 14 second wait_for_silence
:                                                
Waiting up to 4 minutes for new BG: date: invalid
date ‘@’                                        
ls: cannot access /tmp/pump_loop_completed: No su
ch file or directory                             
Radio ok. Listening: .No interfering pump comms d
etected from other rigs (this is a good thing!)  
Preflight OK. Profile less than 60m old. Refreshe
d pumphistory    at node.js:906:3                
and meal.json                                   
Checking pump clock: "2017-10-19T12:16:57-04:00" 
is within 1m of current time: Thu Oct 19 12:16:46
EDT 2017                                        
and that pumphistory is less than 1m old.  Temp r
efreshed                                         
Could not parse input data:  [SyntaxError: /root/
myopenaps/monitor/glucose.json: Unexpected end of
input]                                          
Traceback (most recent call last):               
  File "/usr/local/bin/openaps-report", line 82, 
in <module>                                      
    app( )                                       
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/cli/__init__.py", line 51, in __call__     
    self.run(self.args)                          
  File "/usr/local/bin/openaps-report", line 75, 
in run                                           
    output = app(args, self)                     
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/cli/subcommand.py", line 52, in __call__   
    return self.method.main(args, app)           
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/reports/invoke.py", line 48, in main       
    reporters.Reporter(report, device, task)(outp
ut)                                              
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/reports/reporters/__init__.py", line 33, in
__call__                                        
    self.blob = self.serialize(data)             
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/reports/reporters/__init__.py", line 31, in
serialize                                       
    return self.method.serialize(render(data), se
lf)                                              
  File "/usr/local/lib/python2.7/dist-packages/op
enaps/vendors/process.py", line 56, in prerender_
json                                             
    return json.loads(data)                      
  File "/usr/lib/python2.7/json/__init__.py", lin
e 338, in loads                                  
    return _default_decoder.decode(s)            
  File "/usr/lib/python2.7/json/decoder.py", line
366, in decode                                  
    obj, end = self.raw_decode(s, idx=_w(s, 0).en
d())                                             
  File "/usr/lib/python2.7/json/decoder.py", line
384, in raw_decode                              
    raise ValueError("No JSON object could be dec
oded")                                           
ValueError: No JSON object could be decoded      
supermicrobolus pump-loop failed. pump_loop_compl
eted more than 15m old; waiting for 40s silence b
efore mmtuning                                   
Radio ok. Listening: ............................
..........................No interfering pump com
ms detected from other rigs (this is a good thing
!)                                               
Listening for 40s silence before mmtuning: .No in
terfering pump comms detected from other rigs (th
is is a good thing!)                             
mmtune: "916.516", 5, -71 waiting for 22 second s
ilence before continuing                         
Radio ok. Listening: .No interfering pump comms d
etected from other rigs (this is a good thing!)  
Done waiting for rigs with better signal.        
Unsuccessful supermicrobolus pump-loop at Thu Oct
19 12:21:10 EDT 2017
I'm thinkingmabe still on .git?
cameronrenwick
@cameronrenwick
Oct 19 2017 17:20 UTC
@ecc1 et al. my old 522 would also behave like this. Every battery change needed new complete date and prime. I too think there is a small cap within the design that just looses its ability to store a charge while the battery is out. It was a nuisance for sure but once the date/prime was done worked well.
Samuchco
@Samuchco
Oct 19 2017 17:48 UTC
Dexcom stopped receiving/sending data. --- lines. Yet NS did not register that. In the past the last BG would show with a line crossing. As consequence, OpenAPS did not revert to pump setting and maintained Zero temp. see picture attached
Screenshot (11).png
Screenshot (12).png
the 215 with an arrow up has been like that for close to an hour
Dana Lewis
@danamlewis
Oct 19 2017 17:50 UTC
@Samuchco if data goes missing, what temp is set continues to finish and times out. That's why whatever temp being set is conservative and the safest thing possible at that time, in case data vanishes and it runs to completion.
And as you see the predicted lines show insulin activity kicking in there and a likely low without intervention - that's why it chose a low temp.
garykidd
@garykidd
Oct 19 2017 17:51 UTC
and it looks like it made a good choice anyway since BG seems to have dropped and reset zero temp after re-establishing connectivity
Dana Lewis
@danamlewis
Oct 19 2017 17:52 UTC
It doesn't have data to decide if it's safe to cancel the low temp and revert to normal basal. OpenAPS won't set or cancel temps without data for that reason.
Samuchco
@Samuchco
Oct 19 2017 17:56 UTC
@danamlewis OK. Need to understand the NS issue
Samuchco
@Samuchco
Oct 19 2017 18:07 UTC
Screenshot_20171019-131024.png
Screenshot_20171019-130707.png
Screenshot_20171019-132036.png
Screenshot_20171019-132114.png
Screenshot_20171019-133621.png
Samuchco
@Samuchco
Oct 19 2017 18:12 UTC
notice that the COB pill is Zero, even though he has COB
James
@in-10-city
Oct 19 2017 18:30 UTC
@garykidd did you ever get an answer to your problem? did you recently update? I just updated and my logs are showing errors just like the ones you pasted...
going to re run oref0 setup and see what I get but those errors look quite different from the norm they are not in ~/myopenaps/ or ~/src/
James
@in-10-city
Oct 19 2017 18:42 UTC
@garykidd running "bash oref0-runagain.sh" while in my openaps directory seems to have fixed my issue
cameronrenwick
@cameronrenwick
Oct 19 2017 19:05 UTC
is it just me? I've just onboarded a new battery, new cartridge, new infusion set.. man I'm ready to take on the world... somehow having the insulin pump "full house" just make ya feel bombproof (my non-diabetic friends are jealous I think...)
well... sort of...
James
@in-10-city
Oct 19 2017 19:07 UTC
I wish I could say i can relate, buttt I have 78U left in my pump and.... had to piece a system together on the fly because I left my rig at home.. (thank god for backups)
I am currently hunkered down under my desk with a helmet on waiting for another bomb to drop (in short, wish I was you today but I am still looping)
garykidd
@garykidd
Oct 19 2017 19:12 UTC
@in-10-city got mine rolling . I had the friggin NS site input incorrectly. 4 rigs up functional..2 of which are online as we speak...pretty cool.
cameronrenwick
@cameronrenwick
Oct 19 2017 19:31 UTC
hey.. we've all been there. Ya know how the rigs all communicate properly when they are close? well the other night my back up rig.. that I've physically been building in a new case was just close enough to take over my pump...and the bad part is.. I had done an update but didn't do all the pref.json stuff you do. So underconstruction rig takes over and I wake us a diabetic mess .. so it's clear, work-in-progress rig has some great comms! Just like fighting kids... the loudest always gets their way..
garykidd
@garykidd
Oct 19 2017 19:33 UTC
I used to become stunned at times how far away my TI stick would connect with pump...
the somewhat lackluster RF performance of the explorer board is well-worth the convenience it provides though...by far IMO.
cameronrenwick
@cameronrenwick
Oct 19 2017 19:34 UTC
oh ya.. for sure
garykidd
@garykidd
Oct 19 2017 20:00 UTC
@cameronrenwick funny you've gotten pumped over being fully loaded up...I'm on 0 units (do have a vial of humalog anda syringe though if I can't make it all the way home tonight).
Scott Leibrand
@scottleibrand
Oct 19 2017 20:03 UTC
keep your old reservoirs when you change them out with >0 U left and stash them in your bag etc., and you can use them as emergency backups
cameronrenwick
@cameronrenwick
Oct 19 2017 20:11 UTC
yup +1 on that idea...
is it just me or did the prediction bubbles get more intense with this most recent update? (maybe it's b/c I cleaned my screen? :clap: )
Dana Lewis
@danamlewis
Oct 19 2017 20:16 UTC
hah. there are changes to how SMB's and the purple lines in latest dev(s).
cameronrenwick
@cameronrenwick
Oct 19 2017 20:17 UTC
really like the hover feature... way cool
Dana Lewis
@danamlewis
Oct 19 2017 20:17 UTC
we also moved the cheese on what the purple lines are
Scott Leibrand
@scottleibrand
Oct 19 2017 20:19 UTC
what do you mean by "prediction bubbles getting more intense"?
cameronrenwick
@cameronrenwick
Oct 19 2017 20:20 UTC
they just "look" brighter
Scott Leibrand
@scottleibrand
Oct 19 2017 20:20 UTC
in the rendering branch carb treatments and large boluses are bigger.... no, I don't think we changed that.
cameronrenwick
@cameronrenwick
Oct 19 2017 20:20 UTC
ok...so this IS a LOL... musta been a dirty screen for.. like .. (how long have I been looping??!)
James
@in-10-city
Oct 19 2017 20:21 UTC
Capture.PNG
predictive lines seem the same
Dana Lewis
@danamlewis
Oct 19 2017 20:22 UTC
openaps/oref0#707 for details about what has/not changed
James
@in-10-city
Oct 19 2017 20:22 UTC
carb entries are grapefruits now
Dana Lewis
@danamlewis
Oct 19 2017 20:22 UTC
also depends on when yo updated dev
Scott Leibrand
@scottleibrand
Oct 19 2017 20:23 UTC
and nightscout/cgm-remote-monitor#2926 for details on the NS changes
philipgo
@philipgo
Oct 19 2017 21:24 UTC
@Samuchco If you reinstalled yesterday, you should check whether the autotune directory exists at all. SMB will only work as long as there is an autotune directory.
cd ~/myopenaps && dir
Jon Cluck
@cluckj
Oct 19 2017 23:13 UTC
ugh, I was trying to get SMB/UAM to engage (just to see what it was going to do with a bunch of unannounced carbs), but oref0 is being too effective and it won't work :D
which is super awesome
cameronrenwick
@cameronrenwick
Oct 19 2017 23:24 UTC
thought I had this.. but don't. When I'm here --> nightscout/cgm-remote-monitor#2926 how do I get this to heroku to deploy to my NS. I can only seem to deploy master on my heroku site.. dev just never loads