These are chat archives for nightscout/intend-to-bolus

28th
May 2018
Mikyla
@divishinating
May 28 2018 00:00
@alimhassam thank you. Is there instructions for this somewhere ? I set up http widget and it showed up as Edison with insulin and rig battery
Ashley112885
@Ashley112885
May 28 2018 00:19
What’s the best option to get BG readings on Apple Watch when using Lookout?
alimhassam
@alimhassam
May 28 2018 00:43
@divishinating i'm not sure about where it's documented. All i know there might be a bit of info on some of the pull request where the feature was introduced. Maybe someone else can point to something better... openaps/oref0#923
@Ashley112885 are you using Lookout online, or fully offline? If you're online, then the data will be available in nightscout so you can use any of the nightscout cgm watch faces
if you're offline then i'm not sure.
marafie
@marafie
May 28 2018 00:49
Hi all ... if the oref0 gives more insulin than required (taking into account last meal was 4 hours ago) and the BG goes below the target BG .. the ISF should be adjusted correct?
For example if ISF is 18 mmol/l it should be increased
alimhassam
@alimhassam
May 28 2018 01:27
@marafie are you using autotune?
marafie
@marafie
May 28 2018 01:28
@alimhassam yes
alimhassam
@alimhassam
May 28 2018 01:29
and what is it suggesting?
marafie
@marafie
May 28 2018 01:30
For Basel? Or ISF ?
alimhassam
@alimhassam
May 28 2018 01:30
isf in itself isn't always that important, but it also depends on the carb ratios, and basals... but seems like in this case iyou were asking about the ISF right?
marafie
@marafie
May 28 2018 01:34
Yes
Ali take this example
Last meal 6 hours
Last bolus 6 hours
Target BG 6.5mml/l
ISF 20 mmol/l for each 1 unit of insulin
BG goes down from 9 to 4
Mmol/l
I want to prevent it from going below 6.5
Any suggestions ?
Scott Leibrand
@scottleibrand
May 28 2018 01:48
You can’t make good adjustments based on one data point. Look at what autotune is suggesting, and if you want to make the system less aggressive, then lower your basals and/or raise your CR if autotune is suggesting that.
Ashley112885
@Ashley112885
May 28 2018 03:56
Thanks @alimhassam, trying to figure out if there are any offline watch options that will work with Lookout, maybe Glimpse?
Jason Wittmer
@jbwittmer
May 28 2018 19:55
@jymT1D Did you ever get your communications worked out? You've flashed the TI stick with the appropriate firmware for your frequency? North American pump or WW frequency? Disable the cron job when you're trying to troubleshoot communications. Try 'openaps mmtune' from your openaps directory and see what you get as a response
Jason Wittmer
@jbwittmer
May 28 2018 20:00
@beetraps_twitter Don't know if you got an answer to your question or not. You can certainly reflash the edison with Jubilinux and restart install fresh. Or perhaps you just want to delete your openaps directory without reflashing. rm -rf myopenaps or whatever your directory is called and also remove your /src/ directory and then pull a fresh branch and reinstall.
live4sw
@live4sw
May 28 2018 23:34
I'm getting this kind of warning several times in the past day or two after updating to 0.6.1 enact/smb-suggested.json: {"temp":"absolute","deliverAt":"2018-05-28T23:15:53.057Z","reason":"Warning: currenttemp rate 2.1 != lastTemp rate 0.025 from pumphistory; canceling temp","duration":0,"rate":0}
Anyone have experience with this?