These are chat archives for nightscout/intend-to-bolus

3rd
Jun 2018
Rob Kresha
@rkresha
Jun 03 2018 02:01
@esialb or @/all has anyone had an edison appear to go read only on them, won't boot into OS, flashall to a different version of linux has no affect, gets all the way through and still has the old version on it? If so any tips, almost like when an sdcard goes back and it appears you are writing or deleting files, you eject the card and put it back on and no files have changed like you would've expected
N3FM
@N3FM
Jun 03 2018 02:52
@rkresha , You may want to check that the USB cable in the OTG Port is a full cable with data lines... Try swapping cables... Also make sure the Edison is firmly seated in the mating connector.
Rob Kresha
@rkresha
Jun 03 2018 03:57
@N3FM yeah I'm a technical person, I've got good cables and have several edisons that I have in my fleet, I just have one that is frozen\ up and I'm trying to figure out if I can get it back to a good state
@N3FM I appreciate the suggestion/response, I should've clarified in the original comment. Thanks for taking the time to respond!
Scott Leibrand
@scottleibrand
Jun 03 2018 04:10
@rkresha there might be some nuggets in https://gitter.im/jubilinux/jubilinux (or you could ask there)
Martin Haeberli
@mhaeberli
Jun 03 2018 06:14
requesting reminder on how best to search a gitter channel - gitter app’s search leaves much to be desired, IMHO
alimhassam
@alimhassam
Jun 03 2018 10:57
@rkresha have you tried to reset the partitions to the original layout? Which version are you using?
Press any key when starting up to go to uboot and use command in link above
Rob Kresha
@rkresha
Jun 03 2018 12:45
@scottleibrand good suggestino
@alimhassam I haven't, I'll look into it. I'm on jubilinux 0.2.0 if that is what you're asking. Thanks for the suggestion
garykidd
@garykidd
Jun 03 2018 20:25
assuming you can create wpa_supplicant.conf and ssh file in nano?
hmmmm nano worked as I expected to create wpa_supplicant.conf .....just didnt work for ssh file.....little direction?
Scott Leibrand
@scottleibrand
Jun 03 2018 20:31
touch ssh
garykidd
@garykidd
Jun 03 2018 20:31
just found that---and then run raspi config later to permanentaly enable it---or is that not necessary----thx
marafie
@marafie
Jun 03 2018 22:56
hi.... any idea why mlab is not accessble via heroku?

This page can’t be displayed

•Make sure the web address https://addons-sso.heroku.com is correct.

marafie
@marafie
Jun 03 2018 23:29
@danamlewis i have followed the instructions on http://openaps.readthedocs.io/en/latest/docs/Troubleshooting/Rig-NS-communications-troubleshooting.html to donate and clean up the Mlab. and i still get in NS empty cell for pump and unknown for OpenAps cell any suggestions ?
marafie
@marafie
Jun 03 2018 23:34
i do get allways this for the my NS, and within each 5 mins i go get 3 mins of unknown for my kids NS
fidoman
@efidoman
Jun 03 2018 23:43
Anyone know what all I should check if my g5 sensor is reporting 0 for unfiltered data. This is a brand new sensor insert, batteries freshly replaced and voltage showing perfect on the transmitter?
marafie
@marafie
Jun 03 2018 23:46
@kirkbysound were you able to fix the issue of empty cells in NS ?
fidoman
@efidoman
Jun 03 2018 23:46
BTW. It is showing 0 for filtered data as well, but otherwise Logger is communicating fine with the transmitter. I've tried reseating the transmitter in the sensor once so far.
marafie
@marafie
Jun 03 2018 23:50
@danamlewis it worked by erasing all records