These are chat archives for nightscout/intend-to-bolus

23rd
Oct 2018
tepidjuice
@tepidjuice
Oct 23 2018 04:19
Scott Leibrand
@scottleibrand
Oct 23 2018 04:50
looks like it's a 915MHz u.fl, so I suspect so.
Daniel
@rofid12_twitter
Oct 23 2018 18:42
During my setup of OpenAPS I attached the hat board to the pi zero wh, which caused it to just stop installing
So smart me figured it'd be wise to flash the sd card again using pibakery
But now I'm constantly getting errors while flashing the sd card
I always either get a "can't write to SD-card" or "SD-card not found" error
Even though I formatted the sd card multiple times and deleted all partitions
So that there's one main one instead of a few smaller ones
Also reinstalled pibakery, but all to no avail...
Does anyone know what to do?
mkericson
@mkericson
Oct 23 2018 18:57
Anyone have experience with FIASP and getting it via mail order from Canada? Any Canadian pharmacy recommendations? -- Many Thanks
Abigail Cember
@acember
Oct 23 2018 19:25
@acember
I'm now getting this error: "mmeowlink.exceptions.CommsException: No acknowledgement from pump on wakeup. Is it out of range or is the battery too low?"
My pump had a full battery and was literally touching the rig, so neither or those suggestions apply. If you were following my saga earlier: my mmtune was giving numbers as big as -38, so that wasn't the problem, either.
Dana Lewis
@danamlewis
Oct 23 2018 19:25
This message was deleted
Martin Haeberli
@mhaeberli
Oct 23 2018 19:25
@rofid12_twitter - my only small suggestions are: a) try a different SD card assuming that one got toasted when you ‘hot-assembled’ your system ; b) in future, don’t hot-assemble. keep your system powered off while taking apart and assembling.
Dana Lewis
@danamlewis
Oct 23 2018 19:25
@acember try unseating and reseating the edison on the explorer board. if it keeps happening after that, you may need to reflash ccprog
Abigail Cember
@acember
Oct 23 2018 19:33
Like, physically unscrewing and re-screwing them? And when you say 'reflash ccrpog', you mean this:
wget https://github.com/EnhancedRadioDevices/subg_rfspy/releases/download/v0.8-explorer/spi1_alt2_EDISON_EXPLORER_US_STDLOC.hex
./ccprog -p 16,18,7 reset
./ccprog -p 16,18,7 erase
./ccprog -p 16,18,7 write spi1_alt2_EDISON_EXPLORER_US_STDLOC.hex
Right?
Dana Lewis
@danamlewis
Oct 23 2018 19:46
yes
Daniel
@rofid12_twitter
Oct 23 2018 20:19
@mhaeberli I got it to work now I think, the write was succesful. But now the setup is immensely slow, like I just started the setup and after an hour I haven't reached 70% yet and typing feels very sluggish. Could this be a sign something got fried?
Martin Haeberli
@mhaeberli
Oct 23 2018 20:25
@rofid12_twitter unlikely. The RPi0W is inherently slow, alas. I haven’t re-run this setup in a few months; I assume the instructions DONT have you underclock the device at least not before the install. But I don’t know for sure, and when I did my installs I did it the old fashioned way, not using Pi Bakery. Another trick can be to run the install on an RPi 3 (with a hat installed), then move the SD card over to an RPi0W with a hat. This is because the RPi3 is so much faster.
Daniel
@rofid12_twitter
Oct 23 2018 21:03
I don't have an RPi 3 sadly enough. I don't mind waiting long at all, I had to stop the process after a while because I had to go, so I'll try again tomorrow. But in the documentation it says that it usually takes 10-30 minutes, so that's what's throwing me off. I had a really bad internet connection though, so that might've slowed downloads down, but still not sure why that'd affect the sluggish typing. Even the slowest boards should just be able to type smoothly haha.
Martin Haeberli
@mhaeberli
Oct 23 2018 23:23
@rofid12_twitter :+1: