These are chat archives for nightscout/intend-to-bolus

8th
Mar 2019
tuzoenduro
@tuzoenduro
Mar 08 04:45
Hmm, a little help? Overnight my ns site is not showing rig status or temps or nothing, i haven’t changed anything. Sshing the rig it says it’s looping, but i haven’t seen it enact temps basals
Running 070 dev which was stable until like now
Edit, just saw the pump pepper up and do an smb for eating soon. So it’s looping ok but ns does not show anything, only my bgs
tuzoenduro
@tuzoenduro
Mar 08 04:51
The openaps pill in ns says unknown
Scott Leibrand
@scottleibrand
Mar 08 05:19
Check if you mongo DB is full?
tuzoenduro
@tuzoenduro
Mar 08 05:39
It’s halfway, but ns just came back.
Dunno what happened, i did not do anything to reset or other
TranceCake
@TranceCake
Mar 08 08:08
@tuzoenduro did you update your branch before this happened?
tuzoenduro
@tuzoenduro
Mar 08 09:13
@TranceCake no, did not touch a thing. Went to bed working, woke up not working, mqdre breakfast and it started working again
Made, not madre. Phone and fat fingers
TranceCake
@TranceCake
Mar 08 10:59
hmm, interesting
Stargazer32584
@Stargazer32584
Mar 08 15:34
@cluckj Hey Jon ! YES...i would try it. Because, when i edit the files manually, the errors are the same. And the files are the same like in the example. I guess, the system have some problems with the x12 pumps ?
If anyone uses the openaps - system with an x12 pump..please give me a response... . So we could verify the setup of openaps.
@viq Thank you for your reply. But the site doesn't exist. But i know what you mean. I followed the instructions and edit some "invalid" files manually. But the system will nor run. The failure is unfortunately the same...
Stargazer32584
@Stargazer32584
Mar 08 15:54

@viq Yes...thank you. I've done it. Here is the result after a reboot of the system:

https://drive.google.com/open?id=1Ddc9U-UHrbM8v5svNz0R39xzK5Zyj2ey

Jon Cluck
@cluckj
Mar 08 16:25
I'll be back in front of a computer in like 4 hours, I can help in more detail then :)
Rachel Aumaugher
@theunnaturallog
Mar 08 17:10
Hi friends... with my pi/HAT rig, reboot isn't working. Whether I try it via SSH or on the rig itself, it's like the processes stop (SSH will disconnect) but there's not actually a reboot. I have to hard reset to reconnect or even use the rig. Any suggestions? TIA!
Jon Cluck
@cluckj
Mar 08 17:12
that's a bug with pibakery, doing reboot -f will make it actually reboot
Rachel Aumaugher
@theunnaturallog
Mar 08 17:18
@cluckj Thanks, that worked!
Regarding BT Tethering... do I need to follow the same steps for Edison to pair with my phone?
Jon Cluck
@cluckj
Mar 08 17:20
mostly; bluetoothd doesn't need to be started on the pi0, so skip ahead to the bluetoothctl part
Rachel Aumaugher
@theunnaturallog
Mar 08 17:23
Woohoo I'm tethering again! Thanks for your help :)
Stargazer32584
@Stargazer32584
Mar 08 17:37
@cluckj Thank you for "reboot -f" hint. This was also my problem...
Jon Cluck
@cluckj
Mar 08 17:43
:thumbsup: :clap: :fireworks:
katrina1232
@katrina1232
Mar 08 18:07
Hey guys, new here, trying to install on a pi0. part way through install this happened:
alt
install seemed to continue fine. a while later I got a this segmentation fault:
alt
at a guess I copied the sudo pip command from that final line and it appears to have successfully installed openaps-contrib but the full install has not completed.
alt
anyone able to tell me what's gone wrong/what I need to do to continue installing? cheers
gimme a sec will fix images
first image:
alt
second image:
alt
third:
alt
Scott Leibrand
@scottleibrand
Mar 08 18:40
Was it transient? Does a reinstall get further?
Most of the install commands don’t take too long if they’ve already been done, so you can start over and expect to progress faster.
katrina1232
@katrina1232
Mar 08 18:50
how should I change the install command to retry it when logged in as root instead of pi? copying old one directly gives
bash: /home/pi#: No such file or directory
Stargazer32584
@Stargazer32584
Mar 08 21:05
@cluckj How can i test your experimental stuff for the x12 pump ?
Abigail Cember
@acember
Mar 08 21:10
Is there a way that I can set SMB's maxBolus to higher than 0.2? Is that just a variable I can set in preferences.json?
Scott Leibrand
@scottleibrand
Mar 08 21:10
maxSMBBasalMinutes
Abigail Cember
@acember
Mar 08 21:13
Isn't that the duration in time, though?
Basically, I want to override the "maximum is 30 minutes worth of current basal"...if possible.
@scottleibrand Oh, I just saw your post above about the Bolus Wizard targets not adjusting the sensitivity ratio :(
Scott Leibrand
@scottleibrand
Mar 08 21:18
then set maxSMBBasalMinutes to > 30
Abigail Cember
@acember
Mar 08 21:19
Oh, I see! It's an integral over the basal rate....excellent.
amspoke
@amspoke
Mar 08 21:57
@PedanticAvenger Thanks!
Mags
@111mastermind
Mar 08 23:08
please help total newbie. I've built a raspberry pi with explorer hat and baked the SD card and put it in the rig. but the rig won't boot up when turned on. I've put the microusb cable in both ports and even tried both ports at once. No lights.